Replacement Manual Jack for Atwood Powered Trailer Jack

Question

Question:

Would like to replace my Atwood heavy duty power jack #87083 with a manual jack. Will the Pro Series, A-Frame jackPSRV20000103 work?

asked by: Ray

0

Expert Reply:

Yes the Pro Series A-frame jack part # PSRV20000103 will work great as a replacement for the powered Atwood jack you have now on your trailer. It will easily bolt up in place of it and would have more than enough lifting capacity for your trailer that would weigh up to 7,000 lbs.

For a foot for this jack we have the part # PS1400700340.

expert reply by: Jameson C

0

Answer 1

There is one option that has the right dimensions to replace the Atwood 87891, which is a handle from Stromberg Carlson: - Replacement Crank Handle for Stromberg Carlson Landing Gear #LG-119226 The metal shaft where it attaches to the jack has an…

view full answer...

Answer 2

The Kenda Karrier ST225/75R15 Radial Trailer Tire #AM10303 is made overseas in China. This particular unit features a load capacity of 2,830 pounds at 80 psi and an excellent speed rating of 81 mph. I have attached a short video review on this tire…

view full answer...

Answer 3

I spoke with my contact at MaxxAir regarding the issue you are having with your Deluxe Roof Vent #MA00-07500K. He said the dome not automatically lifting when starting the fan might be related to the temperature you have the unit set at for…

view full answer...

Answer 4

I wish we carried a replacement leg but we do not at this time. Only option we have is a new jack. For a replacement, I recommend the Stromberg Carlson #SC63VR. It has a lifting capacity of 4,500 lbs which would be more than you'd need but will…

view full answer...

Answer 5

Based on your picture you actually have the PD7345 which for a replacement converter section you would want the part #PD4045CSV which is compatible with lead acid and lithium batteries.

view full answer...

Answer 6

Hey Martin, thanks for reaching out. This sounds like an issue with your Progressive Dynamics PD4045K converter system. Since you are connected to shore power we would be looking at something on the AC side of the distribution panel. The fuses and…

view full answer...

Answer 7

The correct replacement control center for your Progressive Dynamics Panel #PD4045KA for the lithium battery style you mentioned is the part #PD4045LICSV. LiFePO4 is a type of lithium battery and has different charging requirements.

view full answer...

Answer 8

Yes, the converter section of the Progressive Dynamics Mighty Mini AC/DC Panel and Converter/Smart Charger #PD4045KA states that it is compatible with lithium batteries. Therefore you can charge your Battleborn lithium batteries with it until you get…

view full answer...

Answer 9

The yellow wire is the wire that connects to the solar panels. I have attached a detailed wiring diagram and demonstration video for the Redarc In-Vehicle BCDC Battery Charger - Dual Input - DC to DC - 12V/24V - 50 Amp #331-BCDC1250D. In regard to an…

view full answer...

Answer 10

Yes the #PD4045CSV can charge a LifePO4 Lithium Iron Phosphate battery when you switch it to Lithium mode. The other converter you mentioned was phased out since it was no longer needed due to the #PD4045CSV having a Lithium mode.

view full answer...

Answer 11

The Replacement Converter Section for Progressive Dynamics 4000 Series RV Power Control Center part #PD4045CSV has a lithium mode that when stitched on will provide a constant charge of 14.6 volts. It does not reduce the charge so you'd need to…

view full answer...

Answer 12

So the #PD4045CSV was recently redesigned so that it could switch between lithium batteries and non-lithium batteries where in the past it was only non-lithium. This is why other part number is getting discontinued.

view full answer...

Replacement Manual Jack for Atwood Powered Trailer Jack

Continue Researching