Triple-Axle Trailer Hanger Kit Recommendation for 7K Axles
Updated 02/26/2013 | Published 02/22/2013
Products Featured in This Question
Question:
WHICH SUSPENSION KIT FOR 7000# 3IN DIA AXELS IN A TRIPLE SET UP? WHAT IS THE CORRECT HANGER SPACING FOR 25IN 6LEAF SPRINGS? THANKS
asked by: ROB S
Helpful Expert Reply:
The Triple-Axle Trailer Hanger Kit # APTT3 that you referenced is designed to work on axles with capacities of 2,000 lbs to 7,000 lbs so it should work very well for you.
I attached a picture that has a chart that shows exactly how you should space the axles when used with a 6-leaf spring like a # e64SR.
From the outer hangers to the inner hanger you will need 24-3/4 inches, in between the two center hangers you will need 29 inches.
Product Page this Question was Asked From
Triple-Axle Trailer Hanger Kit for Double-Eye Springs - 1-1/2" Front/Rear, 2-1/2" Center
- Trailer Suspension Parts
- Hangers
- Suspension Kits
- Boat Trailer
- Camper
- Car Hauler
- Snowmobile Trailer
- Utility Trailer
- Double Eye Springs
- Triple Axle
- etrailer
more information >
Featured Help Information
Miscellaneous Media
Continue Researching
- Search Results: dbc~250~d
- Search Results: ub1250
- Shop: MORryde Rubber Equalizers for Tandem Axle Trailers - 33" Wheelbase - 8K
- Shop: Easy Grease Trailer Idler Hub Assembly for 3.5K Axles - 5 on 4-3/4 - Pre-Greased
- Shop: Demco Hydraulic Brake Hose with Fittings - 19" Long
- Shop: etrailer Sidewind Trailer Jack w/ Drill Adapter - A-Frame - 14" Lift - 2,000 lbs
- Shop: Ultimate Trailer Jack - A-Frame - Topwind - 15-1/2" Lift - 2,000 lbs
- Shop: Easy Grease Trailer Idler Hub Assembly for 3.5K Axles - 5 on 5-1/2 - Pre-Greased
- Shop: Replacement 12-Volt Battery for Curt Soft Trac I and II Trailer Breakaway Kits
- Search Results: scissor hoist
- Search Results: trailer jack
- Search Results: d~rings
- Search Results: weed trimmer racks
- Search Results: 5 hole brake flange
- Q&A: How to Determine the Size of a Trailer Hub Assembly for Replacement
- Q&A: Which Spindle Does Dexter Trailer Hub and Drum Assembly Fit
- Q&A: Meaning of 8 on 6-1/2 Inch Bolt Pattern for Dexter Hub # 8-285-11
- Q&A: Where to Measure When Replacing a Trailer Hub
- Video: All You Need to Know About the Kodiak Disc Brakes
- Video: The Low-Down on the Kodiak Disc Brake Kit
- Video: Feature Review Hydrastar Disc Brake Kit w/ Actuator for Tandem Axle Trailers
- Video: Ultimate Overview of the Kodiak Hydraulic Brake Line Kit
- Q&A: Replacement Hanger Kit, Leaf Springs, Brake Assemblies and Drums for Triple Axle 3,500 lb Axles
- Q&A: Recommended Complete Disc Brake Conversion System For 10,000 lb Dexter Axles
- Q&A: Selecting Correct Bearing Buddy for 8-Lug Hub on 7000-lb Axle on PJ Dump Trailer
- Article: How to Accurately Measure Trailer Leaf Springs
- Shop: Gooseneck Hitch