How To Determine Correct Bearing Kit and Bearing Buddy For 2003 Skeeter 180SX Boat Trailer
Updated 03/13/2021 | Published 03/09/2021
Products Featured in This Question
Question:
I have a 2003 Skeeter 180SX boat and trailer, what bearings, seals, and bearing buddies do I need? Also should I change out the hubs too? Trailer is single axle, no brakes, 5x4.5 bolt pattern. Thank you
asked by: Alwin B
Expert Reply:
I would be happy to help you determine the correct replacement bearings and grease seal, and which bearing buddy will fit the hubs on your 2003 Skeeter 180SX Boat trailer, but unfortunately we do not have a break down of the components used on a specific trailer.
Instead you will need to remove one of your current hubs and looking for the bearing numbers stamped in the face of each bearing as shown in the included picture of the # L44649.
If your bearings are worn to the point that you cannot read the bearing numbers you will need to use digital calipers like # PTW80157 to precisely measure your spindle according to the included diagram.
To confirm the correct grease seal you will need to measure the spindle where the bearing rides, and the location inside of the hub where the seal sits with the # PTW80157 in the locations shown in the included diagram.
Lastly to determine the correct bearing buddy you will need to measure the hub bore of your hubs. I included a picture of where to measure for you to take a look at.
For example the Bearing Buddy Bearing Protectors - Model 1968SS # BB1968SS are designed to fit hub bores that are 1.968" diameter, so if this matches your hub bore this would be a great option for you.
As long as your current idler hub is in good shape there is no reason to replace it, but if you need to replace it I will be able to recommend the correct option with your bearing combination.
If you can tell me your bearing numbers/spindle measurements and hub bore diameter I would be happy to confirm the correct parts for your trailer.
I included a video of the # BB1968SS for you to take a look at.
(click to enlarge)
(click to enlarge)
Product Page this Question was Asked From
Bearing Buddy Bearing Protectors - Model 1968SS - Stainless Steel (Pair)
- Trailer Bearings Races Seals Caps
- Caps
- Bearing Protector Grease Cap
- 1.96 Inch
- 2000 lbs Axle
- 3500 lbs Axle
- Bearing Buddy
more information >
Featured Help Information
Miscellaneous Media
Continue Researching
- Shop: Timken Bearing Kit for Lippert, Dexter, and AL-KO Axles - 3,500 lb with #84 Spindle
- Video: A Closer Look at the Timken Bearing Kit for Lippert, Dexter, and AL-KO Axles
- Q&A: How To Find Correct Bearing Kit for EZ Loader Boat Trailer
- Q&A: Bearing Buddy Recommendation for Hub Bore of 1.97 inches
- Q&A: Solution for Needing Replacement Caliper for Kodiak 204 Caliper
- Q&A: What is Next Size Smaller Bearing Buddy than One with 1.98 inch Outer Diameter
- Q&A: Wet Bolt Recommendation For the Roadmaster Comfort Ride Leaf Spring Suspension Kit
- Article: How to Measure Your Trailer Wheel Bolt Pattern
- Q&A: Replacement Electric Trailer Brakes for a Dexter 8-249 Hub
- Article: Printable Trailer Bolt Hole Pattern Template
- Article: The 5 Best Trailer Drop Hitches You Can Buy
- Q&A: Bearing Buddy Bearing Protectors For a 1.96" Hub Inside Diameter
- Article: How to Replace an RV Roof Vent Cover
- Article: How to Replace or Install an RV Roof Vent
- Article: What are the Common Types of Propane Fittings Used on RVs?
- Article: 30-Amp and 50-Amp RV Service: What's the Difference?