Replacing AL-KO 10 x 1-3/4 Electric Trailer Brakes 2018 Airliner Classic Camper
Updated 08/27/2025 | Published 03/06/2021 >
Products Featured in This Question
Question:
I currently have 10-in by 1 and 3/4-in electric brakes on a camper. These are AL-KO and I no longer find a replacement. Could I purchase an electric unit 10-in x 1.5-in from you and would that be sufficient for a 2,000-lb trailer without having to replace the hubs?
asked by: William S
Helpful Expert Reply:
I must recommend that you replace the hub/drum as well when changing the size of your braking assemblies because the surface area on the old drums may not line up with the new braking assemblies which is why I recommend replacing both at the same time.
The 10" x 1-1/2" braking assemblies part # K23-472-473-00 will use the same four bolt brake mounting flange as the 10" x 1-3/4" braking assemblies you but we no longer have a correct hub for these.
The most common replacement for the 10" x 1-3/4" braking assemblies you have are going to be the 10" x 2-1/4" braking assemblies, part # 23-26-27. The correct hub/drum for this is part # AKHD-545-35-K and this uses a L68149 inner bearing and L44649 outer bearing which is what I believe you have. If this is not what you have please reach our with what you do have and I will make recommendations based on those measurements.
Product Page this Question was Asked From
Dexter Electric Trailer Brakes - 10" - Left/Right Hand Assemblies - 3,000 lbs
- Trailer Brakes
- Electric Drum Brakes
- Standard Grade
- Manual Adjust
- 10 x 1-1/2 Inch Drum
- 3000 lbs Axle
- 13 Inch Wheel
- 14 Inch Wheel
- 14-1/2 Inch Wheel
- 15 Inch Wheel
- Dexter
more information >
Featured Help Information
Miscellaneous Media
Continue Researching
- Search Results: firestone air bag compressor kit
- Search Results: air bag compressor kit
- Search Results: firestone vehicle suspension
- Search Results: firestone air command
- Search Results: air compressor
- Search Results: firestone
- Search Results: on board air compressor
- Shop: Trailer Hitch
- Shop: Vehicle Sway Bars
- Shop: Suspension Enhancement
- Shop: Curt Powered Tail Light Converter with 4-Pole Flat Trailer Connector
- Shop: Trailer Wiring
- Shop: Dexter Electric Trailer Brakes - 10" - Left/Right Hand Assemblies - 3,000 lbs
- Shop: Dexter Electric Trailer Brakes - 10" - Left/Right Hand Assemblies - 3.5K
- Shop: Gooseneck Hitch
- Shop: Curt Trailer Hitch Receiver - Custom Fit - Class III - 2"
- Shop: Camper Tie-Downs
- Shop: Onan Generator - Quiet Series Onboard RV Generator - 3,600 Watts - Propane - CARB Compliant
- Shop: Firestone Heavy Duty Air Compressor - 150 psi
- Shop: Firestone Air Command Heavy Duty Air Compressor with 1/2 Gallon Tank for Self Leveling Systems
- Q&A: Recommended Steering Stabilizer for a 2018 Thor Palazzo 33.2 on a Freightliner 2017 XC-S Chassis
- Q&A: Does Curt Trailer Wiring Harness C98RV Fit 2025 Kia Telluride
- Shop: Vehicle Tow Bar Wiring
- Q&A: Replacement Axle for AL-KO T35 3,500 Pound Axle with 85 Inch Hub Length
- Video: A Closer Look at the Replacement Handle for Curt CrossWing 5th Wheel
- Video: Review of the Replacement Lockable Door for Phoenix Faucets Exterior RV Shower Box
- Video: Review of the WeatherTech Mud Flaps-WT110001
- Q&A: Correct Replacement for 10 Inch x 1-3/4 Inch Braking Assemblies
- Q&A: Replacement Interior LED Lights For a Liteco 179 Florescent Light Fixture
- Q&A: How Does The WeatherTech Hood Protector WT68RE Install On A 2025 Ford Ranger?



Dennis
8/27/2025
i have this situation on my counter and we pulled the AKHD-545-35-K hub out and he thinks he will run out of axle nut thread. Any thoughts? 10x1-3/4 al-ko brakes