Dimensions Of Channel On Demco Hydraulic Brake Actuator DM8759422

Question

Question:

Hi, I would like to ask about this product DM8759422 Could you provide information regarding channel dimensions? Is it 3 wide with 2 spacing ?

asked by: Jakub

0

Expert Reply:

The channel on the Demco Hydraulic Brake Actuator w/ Electric Lockout - Disc - Primed - Adjustable Channel - 8,000 lbs # DM8759422 you were looking at is 2-15/16" wide, 8" long, and the holes are 2" apart center to center as shown in the included diagram.

expert reply by: Samuel C

0

Channel Dimensions Of DM8759422
(click to enlarge)

Answer 1

The Replacement Master Cylinder #DM5918 can be installed on your Demco DA66B surge brake actuator to convert it to work with disc brakes. This includes an electric lockout actuator to prevent the brakes from actuating in reverse.

view full answer...

Answer 2

Hey Warren, so we don't have a recommended size of hardware to use with the Demco Coupler part #DM8104002. This is technically a weld on actuator so your best option would be to have a welder install it.

view full answer...

Answer 3

I went out and measured the actuator #DM8104002 across the top and it's exactly 4 inches like what you're looking for. It's designed to be welded to 3 inch wide trailer tongues.

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 7

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 8

The Demco Hydraulic Trailer Brake Actuator part #DM72VR should be a direct replacement for the Atwood 61101 Brake Actuator that you have now. This newest updated it rated at 7K instead of 6K. This is a bolt on option that mounts on 3" centers.…

view full answer...

Answer 9

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 10

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 11

The manual lockout on your Atwood 85778 surge brake coupler is there so that you can back up the trailer without the brakes locking up on you. Yes you can safely tow your trailer with the broken manual lockout, you just have to make sure you…

view full answer...

Answer 12

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Dimensions Of Channel On Demco Hydraulic Brake Actuator DM8759422

Product Page this Question was Asked From

Continue Researching