Best Way Carry Dirt Bike With 2008 Jeep Compass

Question

Question:

Im looking at your class 3 Draw-Tite 2inch hitch which states a tongue weight of 525 pounds. I believe the Compass manual mentions a limit of 150lbs. Is my limit here the 350 or 150 as Im planning to hook up a dirt bike carrier to the hitch which will be close to the 350 limit?

asked by: Paul

1

Helpful Expert Reply:

Although the Draw-Tite Class III # 75712 has a 525 lb tongue weight capacity, the capabilities of the hitch will be limited by the capabilities of the vehicle its installed on. If the vehicle manufacturers stated tongue weight capacity is lower than that of the hitch, you will need to abide by the lower rating.

I cannot recommend exceeding Jeep's stated tongue weight capacity, as exceeding it could cause the attachment points between the vehicle and the hitch to fail.

A better solution for carrying your dirt bike would be to use a small utility trailer and a wheel chock like part # RA-17 and tie down straps like # EM05729.

expert reply by: Mike L

1

Answer 1

We do get asked that a lot. I haven't heard any plans from B&W to make a Biker Bar like #BWMC2301 for your Goldwing. The haven't done the research and development to make the bar for the frame that attaches to the base with anchor plates.…

view full answer...

Answer 2

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 3

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 4

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 5

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 6

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 7

Hey Bryan, that's a good question. The pricing can definitely be misleading, but I wouldn't use it to judge the quality of the tire. A lot of that comes down to promotions, inventory, and whether you're looking at a tire by itself or…

view full answer...

Answer 8

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 9

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 10

The 5.30-12 tires, being wider, are going to make more contact with the road. This means that the noise, and heat build up will be higher than a 4.80-12 tire but the rolling resistance will actually be less because the tire is larger diameter. The…

view full answer...

Answer 11

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 12

The Demco Hydraulic Trailer Brake Actuator part #DM72VR should be a direct replacement for the Atwood 61101 Brake Actuator that you have now. This newest updated it rated at 7K instead of 6K. This is a bolt on option that mounts on 3" centers.…

view full answer...

Best Way Carry Dirt Bike With 2008 Jeep Compass

Products Featured in This Question

Featured Help Information

Miscellaneous Media

Continue Researching