Replacement Motor for Solera Power Awning of RV

Question

Question:

I have pictures of the motor hoping it helps.

asked by: Kevin H

0

Expert Reply:

Are you sure that's the part number? I wasn't able to find any reference to that. Can you see a brand on the motor?

expert reply by: Jameson C

0

Awning Motor Solera
(click to enlarge)

Kevin H.

2/16/2021

I have pictures of the motor hoping it helps.

Jameson C.

2/16/2021

Thanks for the picture. Based on that we know you need the replacement motor part # LC373566.

Answer 1

We have replacement motors for Solera/Lippert awnings that have a two pin connector like the part #LC373566. This is for awnings that were made after 2015. For awnings made before 2015 we have the part #LC266149. This uses two wires with spade…

view full answer...

Answer 2

Yes you can absolutely grease the gears on your Replacement Motor for Lippert Solera Power Awnings Manufactured after 2015 #LC373566. With that said, it is recommended to use a dry lubricant like the Roadmaster LubeMaster Dry Silicone Spray #RM-747…

view full answer...

Answer 3

I can see from your pictures that you have the Lippert Edge Awning. You can replace just the motor on that awning. The correct replacement motor is the Replacement Motor for Lippert Solera Power Awnings #LC373566. You will need to partially extend…

view full answer...

Answer 4

Based on your needs the TorkLift GlowStep Revolution Uprising Steps w/ Booster Step #TLA9005 is going to be the best solution for you. This fold down step has 5 steps for a 7-1/2" rise/drop, which is the smallest that we currently offer. It fits…

view full answer...

Answer 5

There are other versions of the MORryde StepAbove RV steps that come with a strut assist to make lift and lowering the steps almost weightless and more controlled so that you don't have them come down on top of you. I've listed the options we…

view full answer...

Answer 6

The Solera awnings do not use a spring that applies tension on it so that won't be a concern. What you will want to do when installing the Solera Power Awning Replacement Motor #LC266149 is to bring the awning out about 12 inches or so and then…

view full answer...

Answer 7

Hey Lance, the MORyrde Safe-T-Rail #MR54BR can not be adjusted up or out because it is at a fixed angle. This hand rail measures 54" long and extends off of your RV 42 1/2". What kind of trailer do you have? Please feel free to let me know…

view full answer...

Answer 8

Hey Woody, thanks for reaching out! The MORryde Safe-T-Rail Telescoping RV Hand Rail #MR54BR is more of a universal installation, and will fit RVs that have flat fiberglass walls. It measures 52.2" tall and there are a few other considerations…

view full answer...

Answer 9

Yes, that is absolutely normal and is actually mentioned in the installation instructions. To install the MORryde Safe-T-Rail Telescoping RV Hand Rail #MR54BR you're going to need to: -Remove the existing "Lend-A-Hand" rail. Once…

view full answer...

Answer 10

I'm not quite sure what you got going on but what I can tell you is that in order to install the MORryde Safe-T-Rail Telescoping RV Hand Rail #MR54BR you're looking at, you are going to need: -No trim or obstructions including around a…

view full answer...

Answer 11

Hey Steve, do you know what brand of RV steps you have? If they happen to be the MORryde StepAbove style of steps we have the boot scraper/brush part #MR49RV. Then for a telescoping hand rail we have the MORryde part #MR54BR.

view full answer...

Answer 12

Hello David. It sounds like you are referring to the quick release pin for the MORryde Safe-T-Rail part #MR54BR. This pin is 1/4" in diameter and has 2" of usable length. If you need one, we have them on our site as part #MR35DR.

view full answer...

Replacement Motor for Solera Power Awning of RV

Product Page this Question was Asked From

Continue Researching