Correct Replacement for Atwood Gas Valve 91043

Question

Question:

Will this valve work for the valve mentioned above? Does it come with the fittings shown?

asked by: Randy H

1

Helpful Expert Reply:

The Replacement Gas Regulator for Atwood Gas RV Water Heaters part # 91602 will be a direct replacement for the Atwood 91043. It comes with everything shown in the photos on our product page, the valve/regulator and two fittings.

expert reply by: Conner L

1

Walton S.

4/27/2024

I need water heater valve for a Atwood water heater 91043

Answer 1

The Replacement Gas Regulator for Atwood Gas RV Water Heaters #91602 is the correct replacement for your Atwood 91043. It will be a direct replacement.

view full answer...

Answer 2

If you just got the connector #37185, you would still need about 25 feet of wire #10-2-1, 1 40 amp circuit breaker, #PK54540 and either a 20 amp #PK54520 or a 30 amp #PK54530. Use the 20 amp for 2 to 4 brake assemblies or the 30 amp for 6 to 8…

view full answer...

Answer 3

Hello Celia, I attached the instructions to the Tekonsha Prodigy P2 Trailer Brake Controller - 1 to 4 Axles - Proportional #90885 that you ordered back in 2018, hopefully that is the controller you are working with . They don't really go over the…

view full answer...

Answer 4

The Replacement Gas Regulator for Atwood Gas RV Water Heaters #91602 will actually be a direct replacement for your Atwood 91043 water heater. Current pricing can be found directly on the product page.

view full answer...

Answer 5

The installation time of the Universal Installation Kit for Trailer Brake Controller part #ETBC7 will vary largely by skill level. That said, for a beginner/novice I would estimate around 2-4 hours from start to finish. It's not hard per se but…

view full answer...

Answer 6

For some reason Toyota isn't very forthcoming with how to figure out if you have the tow package or not. From my understanding all of the V6 models of the 2019 Toyota Highlander have the tow package but it isn't specified as to what else…

view full answer...

Answer 7

In order to install a trailer connector and brake controller on a 2018 Jeep Grand Cherokee without tow package you'll need to start with the T-One Vehicle Wiring Harness part #118727 which is plug-n-play. Then, you can adapt this to a 7-way with…

view full answer...

Answer 8

Electric brakes do not use brake fluid. They work by a brake controller sending back voltage to an electro-magnet. When energized the magnet stick to the armature surface of the brake drum. The spinning of the drum pulls out the brake shoes and the…

view full answer...

Answer 9

I can help you install a brake controller like the Tekonsha P3 on your 2015 Jeep Cherokee. For Brake Controller recommendations, I really like the #90195. This brake controller is a proportional controller, which means whatever pressure you press the…

view full answer...

Answer 10

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 11

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 12

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Correct Replacement for Atwood Gas Valve 91043

Continue Researching