Correct Ramp Door Spring for 61" Doorway

Question

Question:

I was looking to get a ramp door spring kit but not sure which size to get. The inside of the trailer from wall to wall is 61. So what size do I need? 5 or 6?

asked by: Javier

0

Expert Reply:

The Conventional Ramp Door Spring for 6' Wide Enclosed Trailer part # 362SA6 is designed for 38" to 69" wide trailer doors so this is what you'll want to use. The bar will actually be trimmed to fit your exact width.

expert reply by: Conner L

0

Answer 1

Trailer ramp door springs are generally chosen based on the inside width of the trailer where it will be installed. Also, ramp door springs such as #362SA6 can be trimmed down some if the length is too much for the trailer. This is the shortest…

view full answer...

Answer 2

I reached out to the manufacturer, who told me the cable was 135 inches long for the Conventional Ramp Door Spring for 5' Wide Enclosed Trailer #362SA5. What you will do is measure from the top of your door down to the bottom of the door and if…

view full answer...

Answer 3

We don't have ability to cut down our trailer ramp springs at this time but we do have a Conventional Ramp Door Spring that does fit your 61 inch wide door that would not require cutting with the part #362SA6 which would work great.

view full answer...

Answer 4

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 7

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 8

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 9

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 10

That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…

view full answer...

Answer 11

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 12

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Correct Ramp Door Spring for 61" Doorway

Product Page this Question was Asked From

Continue Researching