Fulton Hand Wheel Coupler Repair Kit

Question

Question:

My coupler works great. I only need to replace the spring and latch. Is there any such thing available?

asked by: Richard D

0

Expert Reply:

The Repair Kit for Fulton Channel Tongue Coupler with Hand Wheel Latch, 2" to 2-1/8" Ball # F520801 is the only kit available for that hand wheel repair. You will need to get the entire kit as the spring and latch are not available separately.

expert reply by: Jason S

0

Answer 1

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 2

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 3

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 4

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 5

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 6

You can use leaf springs that are rated higher than the axle without any issues as long as they measure the correct measurement for your trailer. For example the 6-leaf double eye spring for 7,000 lb axles part #e64SR measures 24-7/8" eye to…

view full answer...

Answer 7

Trailer wheel bearings are specific to the spindle that is installed on the axle that is on your trailer. You will need to safely support the trailer, remove the wheel and tire, remove the grease cap, remove the cotter pin and washer that secures the…

view full answer...

Answer 8

Hey Donna, yes the Replacement Grease Cap for Dexter/Tie Down Engineering Vortex Trailer Hubs #DE69NR that you referenced does work as a replacement for your Dexter 21-261 cap. How do you like the Vortex trailer hubs?

view full answer...

Answer 9

Hello James, thanks for reaching out. Both the kits you mentioned, the Hydrastar #HYD22FR and #HYD42FR are complete conversion kits for standard 3,500 lb axles. The difference is the calipers included with each kit. The #HYD22FR has stainless steel…

view full answer...

Answer 10

Welcome back Gary. To replace a 2" coupler that fits a 2" wide trailer tongue our options are limited to the Channel Tongue Trailer Coupler item #CT-3001-Z. It's got the standard trigger latch. There's not many options for couplers…

view full answer...

Answer 11

The channel of the Demco 21K #DM16080-52 coupler is 3 inches deep. The distance from the center of where the trailer ball would sit to the first 5/8 inch hole is 7 inches, and 12 inches to the second hole. The Titan #T4853100 dimensions are a little…

view full answer...

Answer 12

Because Buyer's Products considers the build sheets and CAD drawings to be proprietary information, they won't provide copies of that. This being said, I pulled one of the #3370091560 Buyers Products couplers from stock and and measured the…

view full answer...

Fulton Hand Wheel Coupler Repair Kit

Featured Help Information

Miscellaneous Media

Continue Researching