Replacement Grease Seal for a 1.980 Inch Outer Diameter x 1.235 Inch Inner Diameter Grease Seal

Question

Question:

my grease seal is 1.980 o.d x 1.235 i.d. for a 1inch bearing i.d. on a 1inch shaft

asked by: Mike C

0

Expert Reply:

The closest match to the measurements you have provided is # RG06-010. It has an outer diameter of 1.983 inches and an inner diameter of 1.249 inches. To determine if this is correct I would need to know the inner and outer bearing numbers stamped into the metal of each bearing. The initial research I have done indicates that this is most likely the correct seal set but I would need those bearing numbers to be certain.

expert reply by: Michael H

0

Answer 1

I do have an option for you but it sounds like you have a very odd grease seal as the grease seal most commonly used with the L68149 and L44649 bearings is a 58846 which measures 1.719" inner diameter x 2.565" outer diameter. Unfortunately,…

view full answer...

Answer 2

I have included a picture that shows the measurements needed for a spindle, bearings, seals, faces, and hubs. The spindle measurements are labeled A through F. A is the spindle shaft diameter B is where the grease seal sits C is where the inner…

view full answer...

Answer 3

The LMX Red Grease like part #L11390 is the best overall grease for boat trailer applications like you mentioned. It's just as waterproof as any marine grease but is also more heavy duty so it's the way to go for sure.

view full answer...

Answer 4

Hey Eddie, thanks for the pictures. From seeing that I can tell you have a 3,500 lb axle and the correct replacement hub would be the part #AKIHUB-545-35-G-EZ-K that you referenced which comes with new bearings and seal.

view full answer...

Answer 5

Trailer wheel bearings are specific to the spindle that is installed on the axle that is on your trailer. You will need to safely support the trailer, remove the wheel and tire, remove the grease cap, remove the cotter pin and washer that secures the…

view full answer...

Answer 6

You can verify that the 10-19 grease seal included in Bearing Kit #BK2-100 is the correct one for your spindles by taking two measurements. First you want to measure the rear hub bore where the seal is inserted. The seal's outer diameter needs to…

view full answer...

Answer 7

Yes, you certainly can upgrade your single lip seals to be a double lip seal. For that you would want the part #RG06-020 that you referenced.

view full answer...

Answer 8

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 9

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 10

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 11

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 12

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Replacement Grease Seal for a 1.980 Inch Outer Diameter x 1.235 Inch Inner Diameter Grease Seal

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching