Can etrailer E-Track System Install on Aluminum Trailer Floor

Question

Question:

Which E track should be used for aluminum floored trailers? Any concern for steel installed onto aluminum Any tips for install?

asked by: Steve

0

Expert Reply:

The etrailer e-track system # e42VR will work great in your aluminum utility trailer, but you will want to put a layer between the E-Track and the aluminum of your trailer. This layer will help prevent corrosion cause by contact of dissimilar metals. This layer can consist of almost any material, such as wood, rubber, or plastic.

expert reply by: Jameson C

0

Answer 1

On an 4 foot long section of E-track #EM19147 and 2 screws every 16 inches that is a total of 6 screws in the aluminum frame. This most likely will not get you near the capacity of the E-track. I recommend bolting through the aluminum frame so that…

view full answer...

Answer 2

Zinc plated screws are going to be the best option for use with aluminum to resist galvanic corrosion. This corrosion you are referring to is from two dissimilar metals reacting so you want to use the most similar metals when installing your E-track…

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 5

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 6

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 7

Hey Bryan, that's a good question. The pricing can definitely be misleading, but I wouldn't use it to judge the quality of the tire. A lot of that comes down to promotions, inventory, and whether you're looking at a tire by itself or…

view full answer...

Answer 8

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 9

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 10

Hey Jonathon thank you so much for all of that additional information! To haul your bikes behind your class C Sprinter motorhome, while flat towing your Mini, I recommend the Hollywood Racks RV Rider Bike Rack item #HLY64FR and the Roadmaster Dual…

view full answer...

Answer 11

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 12

The 5.30-12 tires, being wider, are going to make more contact with the road. This means that the noise, and heat build up will be higher than a 4.80-12 tire but the rolling resistance will actually be less because the tire is larger diameter. The…

view full answer...

Can etrailer E-Track System Install on Aluminum Trailer Floor

Product Page this Question was Asked From

Continue Researching