Replacement Wheel Studs For Dexter 10,000 lb Drum 9-123

Question

Question:

Hello, Longtime customer here with a few questions: I have a Big Tex trailer with 10k Dexter Axle 8 lug hubs. Each hub with dual tires. I need to replace the wheel studs on them and would like the part number or a link to said studs, I do know they take a 5/8s wheel nut. Also curious if the studs screw out of the hub or are supposed to be driven out? Number on hub is 9-123 if that helps. Thank You

asked by: Calen S

0

Expert Reply:

Hey Calen,

Appreciate the business and we do have the right wheel studs for your Dexter 9-123 hub. They are drive in/press in studs as well, and 5/8" like you mentioned. The correct part for you is the following:

- Replacement Dexter Axle 3-1/2" x 5/8"-18 Press-In Wheel Stud # DX34UR

expert reply by: Kyle S

0

Answer 1

Thanks for reaching out to us, Dale! Thanks for the part number you provided! Unfortunately, 43357 isn’t pulling anything up on mine or Dexter’s end. Do you happen to see any other markings or numbers stamped on the hub itself? We can usually…

view full answer...

Answer 2

Hello Ray, thanks for reaching out. I do know the Dexter 4,400 lb axles and hubs use 1/2" studs, but I do not have a way to look up the Dexter part number or SN to get any specs beyond that. Since we know its 1/2" basically I would just…

view full answer...

Answer 3

The Dexter Trailer Hub and Drum Assembly - 3,500-lb E-Z Lube Axles - 10" - 5 on 4-1/2 - Galvanized #8-247-50UC3-EZ uses 1/2 inch studs so the lug nuts will be 1/2 inch inner diameter and 13/16 inch outer diameter like #CE11051. If instead you…

view full answer...

Answer 4

As long as your wheel doesn't have a specific weight rating listed you can just upgrade your valve stem to a metal one like the Americana Metal, Bolt-In Valve Stem #AM20906 and it will hold up just fine, yes. Most wheels can handle the weight…

view full answer...

Answer 5

On the Dexter Trailer Hub & Drum Assembly, part #8-174-5UC3, the wheel studs are a screw-in stud. The wheel stud would be the Trailer Hub Wheel Stud, part #25-11. This is a 9/16 inch stud that has a total length of 3 inches.

view full answer...

Answer 6

Electric brakes, like part #23-26-27, use 16 gauge wiring. However, we generally recommend using 10 gauge, like part #10-2-1, to connect to the brakes because of how far the wiring generally has to be run. So you need to use butt connectors large…

view full answer...

Answer 7

If the tires are the same size then that matters more than the ply rating, however, we do recommend running the same exact tires on your trailer as that will give you the best performance and most consistent tread wear. For example, you can…

view full answer...

Answer 8

You definitely can Lito! To swap out your manual brakes with self-adjusting ones, you'll want the Dexter Nev-R-Adjust Electric Trailer Brakes item #23-458-459. This is a left and right hand set that will replace one axles brakes. The Dexter…

view full answer...

Answer 9

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 10

The appropriate torque spec for any application will vary depending on the construction of the wheel as well as on the stud size. I suggest checking the wheels you're using to see if their manufacturer has a suggested torque rating. Steel trailer…

view full answer...

Answer 11

I have attached for you below a list of all our 17.5" x 6.75" trailer wheels with an 8 on 6-1/2" bolt pattern below. There are a few different types of wheels in this list such as aluminum/steel, dually/standard, and hub/lug centric.…

view full answer...

Answer 12

I believe you are looking for the correct nut to fit the stud part #007-112-00 which would be the #38N.

view full answer...

Replacement Wheel Studs For Dexter 10,000 lb Drum 9-123

Product Page this Question was Asked From

Continue Researching