Availability of Replacement Lead Jack and Parts for Stromberg Carlson 5th Wheel Landing Gear # LG-1
Updated 02/15/2013 | Published 10/07/2012
Products Featured in This Question
Question:
I gave a fifth wheel trailer with one jack that does not engage. It is the side by the motor. Not sure which side to order the lead or the follow. The jack will work but there is some play when I put pressure to engage. How hard isnitnto change this part out?
asked by: Rich D
Expert Reply:
The jack with the motor is referred to as the lead jack, while the other jack is called the follower. Since the jack on the motor side is in need of replacement, you would need the lead jack. The lead jack is not terribly difficult to replace. You would need to disconnect the drive rod that connects the two legs, remove the lead jack, install the replacement lead jack, and pull the motor and gearbox off the defective jack and install on the replacement.
If you were using the Stromberg Carlson # LG-1, the Replacement Lead Jack is part # LG-179013.
What is wrong with your lead jack? Is the motor still functioning? If the gears in the jack itself are damaged, we offer a Repair Kit, part # LG-146059. A replacement motor, part # LG-217884 or gearbox, part # LG-179015 if needed.
Product Page this Question was Asked From
Stromberg Carlson Electric Landing Gear Set - Weld On - 34-7/8" Lift - 5,500 lbs
- Camper Jacks
- 5th Wheel Camper
- Landing Gear
- Steel
- 5001 - 6000 lbs
- Electric Jack
- 35 Inch Lift
- Weld-On
- 2 Jacks
- Stromberg Carlson
more information >
Featured Help Information
Instructions
Continue Researching
- Search Results: landing gear
- Shop: Lead Jack Repair Kit for Stromberg Carlson Landing Gear
- Search Results: trailer bearings races seals caps
- Search Results: l44649
- Search Results: bearing l44649 and l68149 trailer bearings races seals caps
- Search Results: l44648
- Search Results: bearing l68149 trailer bearings races seals caps
- Shop: Replacement Lead Leg for Venture 5th Wheel RV Landing Gear
- Video: Feature Breakdown: Lead Jack Repair Kit for Stromberg Carlson Landing Gear
- Search Results: ramps
- Q&A: Inner Diameter for the Gears in the Lippert Venture Lead Leg Repair Kit
- Video: Complete Breakdown of the Replacement Lead Leg for Venture 5th Wheel RV Landing Gear
- Q&A: Replacement Parts for a Montana Landing Gear
- Q&A: Venture Bevel Gear Kit Instructions
- Shop: Windshield Wiper Blades
- Shop: Landing Gear Set - 36-1/2" Lift - 8,000 lbs
- Shop: Lippert Venture Follow Leg Repair Kit for 5th Wheel RV Landing Gear
- Shop: Lippert Venture Lead Leg Repair Kit for 5th Wheel RV Landing Gear
- Shop: Replacement Lead Jack w/ Drop Leg for Stromberg Carlson Landing Gear - 29-1/2"
- Shop: Follow Jack Repair Kit for Stromberg Carlson Landing Gear
- Q&A: Repair Kits for Atwood Landing Gear Legs
- Q&A: Diagram to Use when Installing Lead Jack Repair Kit # LG-146059
- Q&A: What Can Damage The Internal Gears Of My 5th Wheel Jack?
- Q&A: Replacement Landing Gear for Frame Clamps That Measure 18-1/2 Inches Apart
- Video: All About the Lippert Venture Lead Leg Repair Kit for 5th Wheel RV Landing Gear
- Video: What to Know About the Lippert Components Tuson High Speed 5th Wheel RV Landing Gear Motor
- Video: Rebuilding etrailer and Ram Sidewind Jacks
- Video: Hands-On with the Replacement Bearing for etrailer and Ram Square Jacks
- Video: All You Need to Know About the Landing Gear Set
Bill
2/10/2013
Hi Mike,Do you have a video guide for lead leg gear repair? Thanks