How To Reset Lippert Ground Control Auto Leveling System
Updated 08/08/2025 | Published 07/29/2020 >
Products Featured in This Question
Question:
Last time we camped the leveling system went out of stroke i did it manually but went to use again time an said to retract lr jack then something else had to do it again manually how do i reset so i can just hit auto level? Thank you
asked by: Mark
Expert Reply:
In order to "reset" your Lippert # LC358590 or # LC675817 Leveling system you'll want to follow these instructions:
1. In manual mode, run the jacks to level the trailer. This is best achieved by placing a level in the center of the trailer and leveling it both front to back and then side to side. (See “Basic Jack Operation” for instructions on how to manually operate the system).
2. Once the trailer is level, turn off the touch pad.
3. With the touch pad off, press and release the “FRONT” button five (5) times and then press and release the “REAR” button five (5) times.
4. The touch pad will flash and beep and the display will read “ZERO POINT CALIBRATION ENTER to set, Power to Exit”.
5. To set the current position as the zero point, press the “ENTER” button.
6. LCD display will read “Zero point stability check”.
7. LCD display will read “Zero point set successfully” once process is complete.
8. The system will set this point as its level state and the touch pad will turn off.
With that said, there may be an issue to where one of the jacks was over-extended and the gears have stripped, which is causing this error on the Left Rear jack. If this continues, please let me know and I can look into this further for you but you may need to replace that leg that is causing you issues.
Product Page this Question was Asked From
Lippert Ground Control 3.0 Electric 5th Wheel RV Leveling System w Touchpad - 4-Point Set
- Camper Jacks
- 5th Wheel Camper
- Stabilizer Jacks
- Steel
- 10001 lbs or More
- Electric Jack
- 36 Inch Lift
- Bolt-On
- 4 Jacks
- Lippert
more information >
Featured Help Information
Instructions
Continue Researching
- Search Results: fcr16dcasa~ss
- Shop: Base Plate for Tow Bar
- Shop: Vehicle Tow Bar Wiring
- Search Results: mouse blocker
- Search Results: brake magnet
- Search Results: brake magnet clip
- Search Results: clearance light
- Shop: Demco LED Tow Light Bar for Towed Vehicles w/ Wireless Transmitter - 12V Power
- Shop: Roadmaster Direct-Connect Base Plate Kit - Removable Arms
- Q&A: What is Needed to Replace Advent Air RV AC Unit with Furrion Chill Cube
- Search Results: rv air conditioners
- Shop: Coleman-Mach Mach-C Everest 18K Air Distribution Box - Ducted or Ductless
- Shop: Trailer Hub & Drum Assembly - 6,000 lbs Axles - 6 on 5-1/2 - Nev-R-Lube
- Shop: Trailer Hitch
- Shop: Easy Grease Trailer Hub and Drum Assembly for 3.5K Axles - 10" - 5 on 4-1/2 - Pre-Greased
- Shop: Global Link RV Baggage Door Slam Latch - Black - 1-3/4" Thick
- Shop: Replacement Drive Head Pin for Solera Power RV Awnings - Regal Style - Qty 1
- Q&A: What Comes With Furrion Chill Cube FR99TD
- Q&A: Is There a Furrion Chill Cube Setup that Works as Both a Dump Setup and Through Ducts
- Q&A: Does The Blue Ox Patriot Braking System Come With A Monitor To Display When The Brakes Are Activated
- Search Results: 008~388~80
- Shop: Nerf Bars - Running Boards
- Shop: Brake Controller
- Shop: Gooseneck Hitch
- Video: Detailed Breakdown of the Replacement Drive Head Motor Gear Pack for Solera Power RV Awnings
- Shop: Vehicle Tow Bar Brake System
- Q&A: How to Clear Retract Time Out Return Levelers Error on LCI Level Up System
- Video: Setting up the etrailer Trailer Hitch Receiver on your 2023 GMC Terrain
- Q&A: How to Reset Zero Point Calibration on Lippert Ground Control 3.0
- Video: A Closer Look at the Blue Ox Leveling Kit with Wheel Chocks


Tom S.
8/8/2025
I successfully completed the reset; however, the auto level still doesn't work. I can manually level all the jacks, though the left rear jack is problematic. Once the other three jacks are down, I have to repeatedly push both the "rear" and the "left" button to lower the left rear jack. The same procedure for raising the LR jack. Since the other jacks seem to lower manually without problem, how do determine where to issue may be? When I first turn the system on, I get an error message telling me to raise the LR jack (despite said jack being fully raised).