Is There a Grease Fitting for the Lock N Roll Articulating Hitches
Updated 02/28/2026 | Published 07/23/2020
Products Featured in This Question
Question:
where on earth is the location to grease this? I cant find on either the truck or trailer side?
asked by: Jeff
0
Expert Reply:
There isn't a grease fitting on the Lock n Roll setups like the part # 336VS501 that you referenced. Greasing it would require manual application in the moving parts.
The LMX grease like the part # L11390 is the toughest and most waterproof so that is what I would recommend.
expert reply by:
Jameson C
0
Product Page this Question was Asked From
Lock N Roll Articulating Trailer Hitch for 2" Receivers - Vehicle Side - 11,000 lbs
- Trailer Hitch Ball Mount
- Fixed Ball Mount
- No Ball
- Steel Shank
- Drop - 0 Inch
- Rise - 0 Inch
- Fits 2 Inch Hitch
- 11000 lbs GTW
- Off-Road Coupler
- Lock N Roll
more information >
Continue Researching
- Search Results: mud flaps
- Search Results: curt trailer hitch
- Search Results: ark trailer jack
- Search Results: trailer breakaway kit
- Search Results: coupon codes
- Search Results: trailer jack
- Search Results: add promo code
- Shop: Tire Chains
- Shop: Mud Flaps
- Q&A: Is etrailer Spare Tire Carrier e98ZR Comparable To Curt c31006?
- Video: Review of etrailer Spare Tire Mount - Hitch Mount Spare Tire Mount - e98ZR
- Video: Checking Out the etrailer Spare Tire Mount for Hitch
- Shop: etrailer Spare Tire Mount for Hitch - 2" Hitch
- Shop: Curt Trailer Hitch Spare Tire Mount
- Video: Review of etrailer Trailer Wiring - 7 Way Upgrade Kit - e99011
- Video: etrailer 7 Way Upgrade Kit With Junction Box Installation
- Shop: Ark Xtreme Off-Road Swivel Trailer Jack w/ Dual Wheel - Sidewind - 7" Lift - 770 lbs - Silver
- Shop: etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector
- Shop: etrailer Electric Trailer Brakes - Self-Adjusting - 10" - Left/Right Hand Assemblies - 3.5K
- Shop: Hub Bearing Kit for Lippert, Dexter, and AL-KO Axles - 3,500 lb with #84 Spindle
- Shop: Timken Bearing Kit for Lippert, Dexter, and AL-KO Axles - 3,500 lb with #84 Spindle
- Q&A: How Many Tire Chains To Use on 2021 Ram 2500 with 35x12.5-17 Tires
- Q&A: Adding Trailer Brakes to a Timbren Axle-Less Trailer Suspension System
- Q&A: How To Add Disc Brakes to Timbren 3.5K Axle-Less Trailer Suspension System
- Q&A: What Hubs And Parking Brake Ready BRakes Go With Timbren 2,200 lb Axle-Less Suspension?
- Q&A: Bearings & Grease Seal For Timbren Heavy Duty 3,500 lb Axle-Less System w/ 4 Lift Spindle
- Q&A: Replacement Bearings, Races & Seal For Timbren 3,500LB Axle-Less Suspension and 6,000LB Trailer Hubs
- Shop: Vehicle Cargo Control
- Video: Review of Weigh Safe Trailer Hitch Lock - Hitch Receiver Locking Pin With Cap - WS54CR
- Video: Detailed Breakdown of the InfiniteRule Hitch Lock for 2" Hitches
Mark
2/28/2026
There are needle zirks on both sides of the locknroll hitch and they do need regular maintenance. Some people change out the needle zirks to regular ones to make it easier to grease the bearings. sometimes the zirks are painted over a bit and you need to clean the the needle hole of the paint if present. Needle adapters are available at Harbor Freight and Amazon.