Can Roadmaster Hy-Power Diode Work with 37 Amps at 10V Input
Published 07/17/2020
Question:
thanks for the response, but the question I was asking if it was OK to run 37VDC through the diode. I have a power supply that has a 37vdc output at 10 amps and I just wanted to know if they voltage rating of the diode will allow for the 37vdc without damaging it since at 12vdc it can handle 1020 Watts, I thought that since at 37vdc at 10 amps is only 370 Watts and it's way under the 1020 Watt. So I think it may work but that's why I am double checking to see if it will work for me.
asked by: Jose R
Expert Reply:
The Roadmaster Hy-Power Diode # RM-790 is rated for a max of 85 amps at 12 volts. If you meant to say 37 amps at 10V then this should work out just fine!
Product Page this Question was Asked From
Roadmaster Hy-Power Diode - (Qty 1)
- Accessories and Parts
- Flat Tow Wiring Harness
- Diodes
- Roadmaster
more information >
Featured Help Information
Miscellaneous Media
Continue Researching
- Shop: Roadmaster Hy-Power Diode - (Qty 1)
- Shop: Replacement Trailer Wheel Bearing Kit, 14125A/25580 Bearings, 14276/25520 Races, Seal 10-36
- Shop: Seaflo Battery Disconnect Switch for Boats and RVs - On/Off - 900 Amps
- Q&A: How to Fix Backfeed From Trailer Battery and Solar Controller on 2024 GMC Sierra 2500
- Q&A: Breakaway Switch Diagram for Installation on a Dump Trailer with Trailer Mounted 12 volt Battery
- Q&A: Specifications for Roadmaster Diodes # RM-690 and # RM-790 for Use on a Semi-Trailer
- Search Results: trailer breakaway kit
- Search Results: breakaway switch
- Search Results: trailer breakaway
- Search Results: diode
- Shop: Trailer Wheel Bearing Kit, LM67048/25580 Bearings, LM67010/25520, GS-2125DL Seal
- Search Results: tarp
- Search Results: roll tarp
- Search Results: roll up tarp
- Shop: Everchill RV Mini Fridge - 4.5 cu ft - 12V - Right Hand Door - Stainless Steel
- Shop: Trailer Hitch
- Shop: Curt Powered Tail Light Converter with 4-Pole Flat Trailer Connector
- Article: Trailer Wiring Diagrams
- Q&A: Lug Nut Torque Chart for Trailer Wheels
- Shop: Trailer Wheel Bearing Kit for Lippert, Dexter, and AL-KO Axles - 3,500 lb with #84 Spindle
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Q&A: What is the Difference Between a Class II and a Class III Hitch?
- Video: Firestone Ride-Rite Air Bags with Easy Mount Compressor Feature Breakdown
- Shop: Trailer Wiring
- Q&A: Comparing Kenda KR03, KR35, And KR53 Tires
- Article: How to Measure Your Trailer Wheel Bolt Pattern
- Shop: Suspension Enhancement
- Article: Wiring Trailer Lights with a 7-Way Plug (It's Easier Than You Think)
- Q&A: Best Suspension Upgrade for 33" Tandem Axles: Road Armor vs Dexter EZ Flex for Ember 22ETS
- Video: Hands-On with the Hub Saver Hub and Wheel Protector
on Accessories and Parts
Jose R.
7/17/2020
thanks for the response, but the question I was asking if it was OK to run 37VDC through the diode. I have a power supply that has a 37vdc output at 10 amps and I just wanted to know if they voltage rating of the diode will allow for the 37vdc without damaging it since at 12vdc it can handle 1020 Watts, I thought that since at 37vdc at 10 amps is only 370 Watts and it's way under the 1020 Watt. So I think it may work but that's why I am double checking to see if it will work for me.