Fulton Replacement Winch Strap for Profile 2000 Winch

Question

Question:

I have profile 2000 for my 24’ Yamaha jet boat which is roughly 500lbs. I snapped the 2” strap and need to know if I can replace with one rated at 1100lbs or more

asked by: Richard A

0

Expert Reply:

As long as the spool on your existing winch will accept a 2 inch wide strap, the Fulton # FWS20HD0200 replacement winch strap would work well for you.

expert reply by: Mike L

0

click to enlarge

Answer 1

You would want to go with the 3 inch Yates Bow Roller for Boat Trailers #YR300Y. This would fit well on your bracket that is 3-5/8 inches with only a little over a 1/4 of an inch of gap on either side of the roller. A 4 inch roller would be too wide…

view full answer...

Answer 2

The width of the roller on the Bow Roller Assembly w/ Bells #YR450Y-400Y that is between the center roller bells measures 3-1/2 inches. This is a super popular size so I would be surprised if this didn't fit your Shorlandr trailer but I'd…

view full answer...

Answer 3

Thanks for the picture! While we do not have an exact replacement for a Profile 2000 winch we do recommend the Dutton-Lainson Hand Winch item #DL14627 as a replacement. This winch has an 1,800 lbs capacity and will work great with the 20' x…

view full answer...

Answer 4

The only repair kit we have for your Profile 2000 hand winch is the Winch Ratchet Repair Kit by Dutton-Lainson item #DL70475. If this isn't what you are needing you will have to replace your winch. I recommend the Dutton-Lainson Hand Winch -…

view full answer...

Answer 5

Part #4769-28 is intended for several models of Fulton winch as listed on the item's page and we have not heard of anyone using it for a Dutton-Lainson winch. Since we do offer a complete D-L winch repair kit #DL70475 that is confirmed to work on…

view full answer...

Answer 6

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 7

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 8

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 9

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 10

The Demco Hydraulic Trailer Brake Actuator part #DM72VR should be a direct replacement for the Atwood 61101 Brake Actuator that you have now. This newest updated it rated at 7K instead of 6K. This is a bolt on option that mounts on 3" centers.…

view full answer...

Answer 11

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 12

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Fulton Replacement Winch Strap for Profile 2000 Winch

Continue Researching