What is 5 on 4-1/2 inch Bolt Pattern for Trailer Wheel

Question

Question:

Can you explain the term 5 on 41/2

asked by: Brendan L

0

Expert Reply:

The bolt pattern of 5 on 4-1/2 inch is the dimensions of the mounting holes of most trailer 5 bolt lug patterns and is what the part # AM30020 that you referenced fits. If you have wheels that are held on with a 5 lug pattern there is a very strong probability you have the 5 on 4-1/2 inch bolt pattern. If you are not sure you can check out the help article that I attached that shows how to determine bolt pattern.

expert reply by: Jameson C

0

Answer 1

Based on the picture you submitted it looks like your trailer was originally intended for a different boat and you'd need to made some modifications to it to get all of the bunks to fit the hull proplerly. The CE Smith Double U-Bolt Bolster and…

view full answer...

Answer 2

Yes, the CE Smith Double U-Bolt Bolster and Swivel Bracket Assemblies #CE10192GA-4 will work as replacements, and you're definitely doing the right thing in replacing them due to the corrosion. You will need to use the CE Smith U-Bolts…

view full answer...

Answer 3

Depends on the stud diameter, if you install the part #AM30040 on a 1/2 axle stud you would want to use 80 ft lbs of torque. If on a 9/16 inch stud you would want to use about 140 ft lbs of torque.

view full answer...

Answer 4

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 5

Hey Andrew, the bracket height is 4.5 inches that you asked about of the CargoBuckle Ladder Rack Straps #CB52MR.

view full answer...

Answer 6

Load range B trailer tires are going to have a lower capacity than C load range tires. Basically that, psi rating, and the ply rating are the only differences. A higher load range tire would last a little longer than lower load ranges of the same…

view full answer...

Answer 7

A larger trailer tire basically wins in every category like you mentioned. Less rolling resistance, less affected by bumps in road for smoother ride quality, and bearings/hub spins less so in theory less wear and tear. So as long as you have room for…

view full answer...

Answer 8

Hi Jim! There is indeed a spare tire and mount for the Malone EcoLight Sport Trailer with Post Style Carrier for 4 Kayaks - 400 lbs #MAL63FR. Check out the Spare Tire for Malone EcoLight Trailer - Locking Attachment #MAL33FR. This will sit flat on…

view full answer...

Answer 9

For your trailer wheel and tire that has the size 4.80-8 on a 4 lug wheel the part #AM30000 would be a great option. Those tires definitely look like they need to be replaced!

view full answer...

Answer 10

For your application I recommend using the Kenda 165/65-8 Bias Trailer Tire with 8" White Wheel #AM3H200 as it will be a little larger but not large enough to cause clearance issues like a tire that fits a 10" wheel would (the 10"…

view full answer...

Answer 11

The 4.00-8 tire is an obsolete size that is no longer manufactured. The name 4.80/4.00-8 is used so people will know that the new size which has a tread width of approximately 4.8 inches is the correct replacement that would be slightly wider than…

view full answer...

Answer 12

The special trailer (ST) tires will have a maximum speed rating of 65 miles per hour, unless stated otherwise on the tire. It is not recommended to run a trailer tire at a higher speed than 65 miles per hour due to the heat buildup that will occur…

view full answer...

What is 5 on 4-1/2 inch Bolt Pattern for Trailer Wheel

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching