Does the Dexter Trailer Springs Over-Under Conversion Kit Require Welding

Question

Question:

Does this kit need to be welded to the axle? Or will it stay in place he way it is designed

asked by: John B

0

Expert Reply:

The Dexter Trailer Springs Over-Under Conversion Kit like part # K71-384-00 does not require welding. That said, it is recommended to tack the spring seats to the axle but this is super easy to do even for someone with no prior welding experience. It is however not required, only recommended.

expert reply by: Conner L

0

Answer 1

Yes, you can replace a square axle with a round beam axle so long as it is rated appropriately. You will need a new u-bolt kit for the round 2K axle, part #APUBR-10. We offer beam axles rated up to 3500-lbs and also axle-less suspension kits from…

view full answer...

Answer 2

Yes, you can replace a trailer's round axle with a square axle as long as the weight capacity is appropriate. You will need a new U-bolt kit to connect the axle: 1-1/2 inch square axles #CE23102 1-3/4 inch square axles #175130 for the U-Bolts and…

view full answer...

Answer 3

You are correct that the spring seats included in an over/under conversion kit like the Dexter Trailer Springs Over-Under Kit #K71-384-00 should be tack welded on in most cases. I checked with one of my engineering contacts over at Dexter and he did…

view full answer...

Answer 4

Hey Christopher, Does your Lantern have a leaf spring suspension or torsion axle suspension? If you have a leaf spring suspension and your axle sits above the leaf springs then you can use an over-under-conversion kit #K71-384-00 (2-3/8"…

view full answer...

Answer 5

Typically if you are going to increase your tire size on your 2024 Coleman 17B you are going to have to raise the suspension to get the clearance for larger diameter tires. As your Coleman has an under slung axle the Axle Flip Kit #K71-384-00 would…

view full answer...

Answer 6

For your 2021 Keystone Passport SL Travel Trailer with an entry height of 32" and door width of 24", yes, the correct the MORryde StepAbove RV Steps, #MR98RR is for 23-3/4" to 26-1/4" wide doorways and entry height of…

view full answer...

Answer 7

Thank you for the images. The MORryde Rubber Equalizers #MR87ZR are the correct set for your 2020 Keystone Outback Ultra-Lite 291UBH. You will pair this with the MORryde Suspension Upgrade Kit #MR46ZR. Instead of using the wet bolts included with the…

view full answer...

Answer 8

Hi Shane; for an over/under kit for your 2-3/8" diameter trailer axles what you will need is the following: - Dexter Trailer Springs Over-Under Conversion Kit #K71-384-00 Keep in mind this kit is for a single axle only, so for a tandem axle you…

view full answer...

Answer 9

Yes, axle spread and wheel base by definition are the same measurements. You will measure from the center of one axle to the center of the 2nd axle to determine what you axle spread is. This may be difficult as some wheels and covers will make this…

view full answer...

Answer 10

With the MORryde Rubber Equalizers #MR87ZR being taller than a traditional Curved Equalizer #TREQ458 will raise the ride height on your trailer if you use your current shackles and straps. MORryde does make the Suspension Upgrade Kit #MR76ZR with…

view full answer...

Answer 11

We do have a way for you to lift your trailer with what are 2-3/8" diameter axles (which is the size of 3,500 lb axles as there aren't 2-1/2" axles I'm aware of), though not with lift blocks with longer U-bolts. Instead, you would…

view full answer...

Answer 12

Yes, if you wanted to drill a different hole in your trailer suspension rear hangers you could and this would allow the spring to be held at a different height. Just make sure it's not too close to the current hole.

view full answer...

Does the Dexter Trailer Springs Over-Under Conversion Kit Require Welding

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching