Replacement Circuit Board for MaxxAir MaxxFan 4401K

Question

Question:

Hi, do you carry the printed circuit board for the Maxxair MAOOAOO4401K?

asked by: Rod B

0

Expert Reply:

Yes. The Replacement Printed Circuit Board and Switch for MaxxFan Roof Vents # MA10-04301k-v16 is the printed circuit board you need.

expert reply by: Jason S

0

Answer 1

Based on the part number of your motor the correct circuit board would be the part #MA10A21275K.

view full answer...

Answer 2

If you have a MaxxAir MaxxFan Plus RV Roof Vent (00-04500K, 00-04700K, 00-04800K, 00-04900K, 00-07000K, 00-07500K, 00-08500K, 00-08700K, and 00-08900K) then you can use the Replacement Wall Control Panel for MaxxAir MaxxFan Plus Roof Vent part…

view full answer...

Answer 3

Based on what you described it sounds like you are looking for the part #MA10-04301k-v16 which is a two switch setup attached to a circuit board for MaxxFan roof vents like what you have.

view full answer...

Answer 4

I think you have the MaxxFan Roof Vent w/ 12V Fan #MA00A04401K, I didn't find anything using the ma00-04401k number you provided. But that ma00-04401k number is only one digit off of #MA00A04401K. The correct replacement board for the…

view full answer...

Answer 5

According to the manufacturer, if the controls are not working correctly the circuit board Item #MA10-04301k-v16 is malfunctioning on your MaxxFan Roof Vent Item #MA00A04301K. Since you have replaced the circuit board already and it is doing the same…

view full answer...

Answer 6

Based on the problem you are having with your MA00-05100K Maxxair fan what you would need to fix it would be a replacement circuit board which would be the part #MA10A21276K.

view full answer...

Answer 7

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 8

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 9

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 10

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 11

Both the Roadmaster and Blue Ox tow bars are great options. But if it was my decision to make I would go with the Blue Ox Avail part #BX7420 as we have found that the Blue Ox tow bars are a little easier to connect and disconnect from. Also this tow…

view full answer...

Answer 12

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Replacement Circuit Board for MaxxAir MaxxFan 4401K

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching