Which Curt Trailer Wiring Harness Fits 2012 Jeep Liberty

Question

Question:

Hello, just recently I purchased through Home Depot a combination class 3 curt trailer hitch and a wiring harness for my 2012 Jeep Liberty. I had to return back my wiring harness which had a number 55382 on the package. The connectors weren’t compatible with my vehicle. I need to know what number of wiring harness I need for my vehicle.

asked by: Bob S

0

Expert Reply:

The correct Curt trailer wiring harness you need for your 2012 Jeep Liberty is the part # C56334 as the kit you tried is actually for older model Liberties and is why the connectors don't match up.

expert reply by: Jameson C

0

Answer 1

To install the #118384, you would need to unplug your existing 7-way harness from the rear of the socket. The #118384 would plug inline between the vehicle harness and the existing 7-way, as shown in the video I linked you to. If your Liberty does…

view full answer...

Answer 2

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 3

Thanks for reaching out, Jack! What I recommend using is the Curt Adapter #C57672 and securing it to your vehicle with the No-Drill Bracket #18136. This gives you the ability to seamlessly use either the 4-Way or 7-Way connection but doesn't…

view full answer...

Answer 4

Hey Tim, You can for sure add a 7-way to your 2019 Jeep Grand Cherokee that already has the Curt T-Connector 4-Way #C62VR on it. Are you looking to utilize the electric brakes on your trailer's 7-way? If not you can just use an adapter, the…

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

If you just need a 4-pin to 7-pin trailer wiring adapter, then you can use part #C57672. This will plug into the 4-pin trailer connector on your brother's vehicle and give him the 7-pin socket for the trailer. Keep in mind, this will only give…

view full answer...

Answer 7

Good news, I can help you figure out how the Draw-Tite Hitch #75578 will mount on your 2012 Jeep Liberty Sport. You are correct, if the hitch has to protrude then the more economically priced Curt hitch #13245 will be a good solution for your…

view full answer...

Answer 8

It's pretty simple. A 4-bolt rail uses four 5/8 inch bolts ran through the floor of the truck bed into the frame brackets. The bolts run down through the center of the raised part of the rail, as shown in the photo I provided. A 10-bolt rail uses…

view full answer...

Answer 9

Hey Patrick, in that case what you would want is just the part #ETBC7L which is the correct 7-way adapter and comes with just the parts needed to activate the circuit needed for the RF controller to work.

view full answer...

Answer 10

If the trailer you will be towing with your 2017 GMC Savana 2500 Van has brakes then yes, you will need to use a 7-way wiring harness and brake controller in addition to the trailer hitch, trailer wiring harness, and ball mount/hitch ball. These will…

view full answer...

Answer 11

I took a couple measurements on the hitch receivers themselves and compared it to the measurements we made when we installed them on Jeeps to determine if there's a difference. We've installed the Draw-Tite #75578 on a 2008 Jeep Liberty and…

view full answer...

Which Curt Trailer Wiring Harness Fits 2012 Jeep Liberty

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching