Recommended Bolts To Secure Titan Zinc-Plated Coupler Part # T2343400183

Question

Question:

i didnt see anything about mounting hardware... What bolt specs do you recommend? Diameter, length, grade?

asked by: Andy R

0

Expert Reply:

The hardware for the Titan Zinc-Plated Coupler part # T2343400183 is not included. For this, I recommend 1/2" x 3-1/2" Grade 5. This can be obtained at pretty much any local hardware store.

expert reply by: Conner L

0

Answer 1

The channel of the Demco 21K #DM16080-52 coupler is 3 inches deep. The distance from the center of where the trailer ball would sit to the first 5/8 inch hole is 7 inches, and 12 inches to the second hole. The Titan #T4853100 dimensions are a little…

view full answer...

Answer 2

The Titan Zinc-Plated Straight-Tongue Coupler, part #T4853100 is designed to fit a 3 inch wide channel tongue on your trailer. This entire coupler is rated for 21,000 lbs, not just one component. I called my contact at Titan and they told me that…

view full answer...

Answer 3

I went out to the warehouse to take some measurements of the Titan Zinc-Plated Straight-Tongue Coupler #T4853100 for you. Based on the measurements, the Titan #T4853100 will not fit into a 4 inch square tube. The width of the coupler is 3-3/8 inches.…

view full answer...

Answer 4

There's no adjustments or replacement parts available for the Dexter Zinc-Plated Straight-Tongue Coupler item #T4853100 you were looking at. If this is the same one that's on your trailer I do recommend replacing it if you are concerned about…

view full answer...

Answer 5

The Titan Straight-Tongue Coupler, part #T4853100, is designed for a 2-5/16 inch ball and a 3 inch wide trailer tongue. It has a weight capacity of 21,000 lbs. I spoke with my contact at Titan and he said that the coupler was tested with all five…

view full answer...

Answer 6

The bolt pattern showing two slightly higher holes 3 inches on center and two slightly lower and larger holes 5 inches on center from each other is the proper bolt pattern. The part that actually fits over the trailer tongue has an internal width of…

view full answer...

Answer 7

Hey Jim, I attached a picture that has the dimensions between the mounting holes of the Demco Channel Coupler part #DM15931-52 that you referenced. Are these the dimensions you are looking for?

view full answer...

Answer 8

The Titan Straight Tongue coupler part #T4853100 uses the exact same bolt pattern as your Titan surge coupler so this would be the easiest solution to convert your trailer to electric to hydraulic. If you haven't picked out an actuator setup the…

view full answer...

Answer 9

The Titan Zinc-Plated Straight-Tongue Coupler #T4853100 that you referenced weighs 14 lbs and has a 21,000 lb total trailer weight capacity.

view full answer...

Answer 10

The Titan Extended 2-5/16 inch Bolt On Coupler, #T4853100, is rated for 21,000 pounds capacity. To be able to tow that much weight, all components would need to be rated for at least 21,000 pounds including the tow vehicle, the hitch, the ball, all…

view full answer...

Answer 11

We do have everything you need to convert to 12" electric over hydraulic drum brakes for your boat trailer: - Hydraulic Brake Kit 12" - Free Backing #AKFBBRK-7-D - Mounting Bolts and Hardware for 12" Brake Assemblies #BRKH12 -…

view full answer...

Answer 12

I went out to the warehouse to determine the mounting pattern of the Model 6 actuator and the coupler, #T4853100.I have included a picture below that shows the bolt patterns. The 2 holes are at 1.031 inches, the last 2 holes are at 1.25 inches and…

view full answer...

Recommended Bolts To Secure Titan Zinc-Plated Coupler Part # T2343400183

Continue Researching