Replacement Axle for LoadRite Boat Trailer
Published 05/15/2020
Products Featured in This Question
Question:
Thanks very much for the follow up. The specs on the axle are: Spring Axle 72” spring to spring 2”x2” square axle (with dip in it) Appears to be 86” hub face to hub face I don’t have a caliper, but the spindle appears to be 1 ¼ (seal) to 1 1/8 (inner/outer) The axle is basically 90” long total 2001 LoadRite trailer Thanks again for your help. I just want to make sure I get something that works. Thanks!
asked by: Allen M
Expert Reply:
I looked up the LoadRite parts and they have torsion axles and traditional spring axles. If you have a trailer that has the springs centered at 58 inches on center and is 1-1/2 inches square, then the axle is a 2,000 lb axle and you would use the Dexter Trailer Axle Beam with Standard Spindles - 72" Long - 2,000 lbs # T20BTR-7258 with hardware # APUBR-10.
If you have different axle, give me those measurements and I'll try to assist by comparing parts. Overall length, style of springs whether traditional or as integrated torsion axle, springs from center to center, and diameter or axle dimension. I believe all the axles are square with that manufacturer.
Product Page this Question was Asked From
Dexter Trailer Axle Beam with Standard Spindles - 72" Long - 2,000 lbs
- Trailer Axles
- Leaf Spring Suspension
- Standard Grade
- No Hubs
- 2000 lbs
- Spindles Only
- 58 Inch Spring Center
- 72 Inch Hub Face
- No Drop or Lift
- Dexter
more information >
Featured Help Information
Miscellaneous Media
Continue Researching
- Search Results: leaf spring bushing
- Search Results: trailer breakaway
- Search Results: 3500lb leaf spring
- Search Results: trailer breakaway switch
- Shop: Dexter Heavy Duty Suspension Upgrade Kit for Single Axle Trailers -3-1/8" Shackle Straps
- Search Results: trailer suspension parts
- Search Results: trailer axles
- Q&A: How to Determine Correct Hub Replacement for 1994 Jayco Eagle SD with Dexter Axle
- Shop: Dexter Trailer Axle Beam with EZ-Lube Spindles - 89" Long - 3,500 lbs
- Shop: U-Bolt Kit for Mounting 3,500-lb, Round Trailer Axles - 5-1/2" Long U-Bolts
- Search Results: spare tire mount
- Shop: CE Smith U-Bolt Kit for Mounting 3,500-lb, Round Trailer Axles - 5-1/2" Long U-Bolts - Zinc
- Shop: 4-Leaf Double-Eye Spring for 3,500-lb Trailer Axles - 25-1/4" Long
- Shop: #84 Spindle for 3,500-lb Trailer Axles - 2" Diameter
- Shop: Trailer Idler Hub Assembly for 3,500-lb Axles - 5 on 4-3/4 - Pre-Greased
- Q&A: 72" Hub Face Trailer Axle With 60" Spring Center and Idler Hubs
- Q&A: Replacement Axle Components For Dexter D80 8,000LB Axle Under 2016 Landmark Orlando 5TH Wheel
- Article: How to Measure a Trailer Axle
- Q&A: Replacement Trailer Hub Assembly for Dexter 8-248 Hubs
- Q&A: How to Check for a Bent Trailer Axle Spindle
- Q&A: Replacement Hub for 1989 Ranger Trailer
- Q&A: Where to Find The Axle Serial Number On Dexter Axles Manufactured After April 2001?
- Article: How to Measure a Boat Trailer Axle
- Article: 30-Amp and 50-Amp RV Service: What's the Difference?
- Article: Wiring Trailer Lights with a 7-Way Plug (It's Easier Than You Think)
- Article: How to Raise Your Travel Trailer Height
- Article: 5 Tell-Tale Signs It’s Time to Replace Your Trailer’s Leaf Springs
- Article: Trailer Lighting Requirements
Allen
5/15/2020
Thanks very much for the follow up. The specs on the axle are: Spring Axle 72” spring to spring 2”x2” square axle (with dip in it) Appears to be 86” hub face to hub face I don’t have a caliper, but the spindle appears to be 1 ¼ (seal) to 1 1/8 (inner/outer) The axle is basically 90” long total 2001 LoadRite trailer Thanks again for your help. I just want to make sure I get something that works. Thanks!