Does Replacement Rod and Nut # TJD-12000-RODNUT Fit 12k Ram Jack

Question

Question:

I have a RAM Weld on Trailer Jack Model 12000 Series will the Part # TJD-12000-RODNUT be the correct replacement part # Thanks

asked by: Jeff G

0

Expert Reply:

Yes, the # TJD-12000-RODNUT is the correct replacement for your 12 Ram jack. This is a replace nut and screw.

expert reply by: Jameson C

0

Answer 1

The Ram Trailer Jacks generally use a 1" diameter threaded rod whereas the Bulldog Trailer Jacks generally use a 1-1/4" threaded rod. Therefore, it would appear as if you have a Bulldog Trailer Jack and in which case the Replacement Screw…

view full answer...

Answer 2

Hey John, the replacement gear kit you'd need is the part #TJD-12000-RODNUT which I attached two pictures that have instructions and an install diagram.

view full answer...

Answer 3

The Bulldog Replacement Sidewind Gear Kit #BD500212 that you referenced is the correct repair kit for your Bulldog square tube jack according to my contact at Bulldog. The top cap you can use is part #BD017802. After you repair the jack you will want…

view full answer...

Answer 4

We do not have this item in stock for me to measure its thread pitch but two of us estimated it as being 6 or 7 threads per inch. I linked a photo of the instructions to replace this part. The bearing is removable and is available as a replacement…

view full answer...

Answer 5

The Ram 12k Jack will use the Replacement Square, Direct Weld Jack Inner Tube with Spring-Return Drop Leg #TJD-12000SP-FIP.

view full answer...

Answer 6

We have several replacement parts for the internals of a Ram brand square jack. The Replacement Rod and Nut #TJD-12000-RODNUT will fit the following Ram jacks: #TJD-12000SP-F2 10K Sidewind with 12-3/8 inches of travel w/handle #TJD-12000SP-R2NH 10K…

view full answer...

Answer 7

Trailer hub and drum assembly #8-201-5 does match your bearings. I am fairly certain you have 5,200 pound axles and not 3500 pound axles since all of the parts you need are for higher rated axles than 3500 pounds. The races come already pressed into…

view full answer...

Answer 8

The bearing is not included with the Replacement Rod and Nut for etrailer and Ram Square, Direct Weld Jacks - 12K part #TJD-12000-RODNUT. There is a bearing washer at the top but the bearing is sold separately as the Replacement Bearing for etrailer…

view full answer...

Answer 9

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 10

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 11

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 12

You can use leaf springs that are rated higher than the axle without any issues as long as they measure the correct measurement for your trailer. For example the 6-leaf double eye spring for 7,000 lb axles part #e64SR measures 24-7/8" eye to…

view full answer...

Does Replacement Rod and Nut # TJD-12000-RODNUT Fit 12k Ram Jack

Product Page this Question was Asked From

Continue Researching