Orientation of the Replacement Thrust Bearing for Square Bulldog Jacks

Question

Question:

I took the old bearing out and am not sure which side was the top side? My bearing had a thrust washer on it and i would assume the washer should go opposite the part #? And the part # should face the bottom end of the jack? Is that correct? Thank you!

asked by: Francis K

0

Expert Reply:

I spoke to my contact at Bulldog and he informed me that the washer will go opposite the part number and the part number will face up.

The reason the number should face up is so the bearing does not hold water.

expert reply by: Jameson C

0

Answer 1

Hey William, the thrust bearing part #TJD-7000-BR that you referenced is 1/2 inch thick. If you are trying to verify this is correct fit by it's dimensions it's worth mentioning that the outer diameter is 1.519 inch and the inner diameter is…

view full answer...

Answer 2

I see that you got the Replacement Cap for etrailer and Ram Square, Sidewind Jacks #TJD-7000S-CP, which indicates that you have a square side crank jack. I have listed the square jack thrust bearings that we have below, along with their OD/ID, we do…

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 5

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 6

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 7

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 8

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 9

Hey Jonathon thank you so much for all of that additional information! To haul your bikes behind your class C Sprinter motorhome, while flat towing your Mini, I recommend the Hollywood Racks RV Rider Bike Rack item #HLY64FR and the Roadmaster Dual…

view full answer...

Answer 10

Hey Bryan, that's a good question. The pricing can definitely be misleading, but I wouldn't use it to judge the quality of the tire. A lot of that comes down to promotions, inventory, and whether you're looking at a tire by itself or…

view full answer...

Answer 11

Hey Jon; I was actually just talking to Furrion about heat options for the Chill Cube yesterday (1/21/2025). At this time, the only way to have heat with this unit is through a furnace on a ducted setup. The Furrion Chill Cube RV AC w/ Air…

view full answer...

Answer 12

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Orientation of the Replacement Thrust Bearing for Square Bulldog Jacks

Continue Researching