Distance Between Mounting Holes on Shank of Flash Solid Steel 2-Ball Mount # FA49-00-5625

Question

Question:

what is the center to center hole distance on height adjustments?

asked by: Donald W

1

Helpful Expert Reply:

The adjustment holes on the Flash Solid Steel HD Adjustable 2-Ball Mount # FA49-00-5625 that you referenced are separated by 1-5/16 of a inch.

expert reply by: Jameson C

1

click to enlarge

Answer 1

From the center of the hitch pin hole on the Fastway Solid Steel 2-Ball Mount #FA49-00-5625 to the point where the shank starts to drop down vertically there is a distance of 3 inches. From the center of the hitch pin hole to the outer edge of this…

view full answer...

Answer 2

In regards to the Flash Solid Steel HD Adjustable 2-Ball Mount part #FA49-00-5925, the distance from the top of the shank to the bottom of the vertical adjustment shaft is 13-1/2". I have attached a photo below.

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 5

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 6

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 7

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 8

Hi David! There are quite a few hitches offered for your 2026 Honda Odyssey, so I definitely understand wanting to know the differences. There are basically three styles available for you and I have them broken out below: Exposed Crosstube: etrailer…

view full answer...

Answer 9

Hey JC, thanks for reaching out! The B&W Tow & Stow 2-Ball Mount #BWTS20066BMP is definitely compatible with the MultiPro tailgate on your 2024 GMC Sierra 2500, but the only one available to fit exactly with a 2-1/2" hitch receiver is…

view full answer...

Answer 10

Hey Matt, welcome back! You are correct. The threaded hole on the Weigh Safe 180 Hitch 2-Ball Mount for 3" Hitch item #WS34MR ball retainer, is to make removing the pin easier. You can insert a 1/4"-20 screw to get additional leverage to…

view full answer...

Answer 11

Hi Cory, can you tell me the specific part numbers and which measurements you want exactly? I only see that you looked at some Trimax HD ball mounts, and I want to make sure I'm getting all of the measurements you're looking for and on the…

view full answer...

Answer 12

Thank you for the photos and sorry to hear about your truck! The unique design of the B&W Tow & Stow 2-Ball Mount - Compatible with GM MultiPro Tailgate #BWTS20066BMP is that angled section that meets with the shank part of the ball mount. On…

view full answer...

Distance Between Mounting Holes on Shank of Flash Solid Steel 2-Ball Mount # FA49-00-5625

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching