Distance From Hitch Pin Hole to Vertical Adjustment Shaft on Fastway Ball Mount # FA49-00-5625

Question

Question:

what is the distance from the center of the hitch pin hole to the face of the vertical bar? I need to know if my Rock Tamers will fit. thanks!

asked by: Steve

0

Expert Reply:

From the center of the hitch pin hole on the Fastway Solid Steel 2-Ball Mount # FA49-00-5625 to the point where the shank starts to drop down vertically there is a distance of 3 inches. From the center of the hitch pin hole to the outer edge of this vertical post there is a distance of 5-3/4 inches.

I have attached an image to assist.

expert reply by: Chris R

0

click to enlarge

Answer 1

The adjustment holes on the Flash Solid Steel HD Adjustable 2-Ball Mount #FA49-00-5625 that you referenced are separated by 1-5/16 of a inch.

view full answer...

Answer 2

In regards to the Flash Solid Steel HD Adjustable 2-Ball Mount part #FA49-00-5925, the distance from the top of the shank to the bottom of the vertical adjustment shaft is 13-1/2". I have attached a photo below.

view full answer...

Answer 3

The Curt Adjustable 2-Ball Mount #C45902 is manufactured overseas. If you are looking for a similar made in the USA adjustable ball mount the Flash Solid Steel HD Adjustable 2-Ball Mount #FA49-00-5625 has the same 2-1/2" receiver, 6" drop,…

view full answer...

Answer 4

Curt recommends the use of 250 ft/lbs of torque when tightening the nuts of their hitch balls with a 1 inch diameter shank like the part #C40034 that you referenced. The general rule is for a 3/4" shank tighten to 150 ft/lbs For a 1" shank…

view full answer...

Answer 5

Hey Steve, yes a Rock Tamers mud flap kit like the part #RT47VR would work with the Weigh Safe adjustable ball mounts part #WS68RR and #WS56ZR. The ball mounts have enough clearance on the shank to allow the Rock Tamers to fit.

view full answer...

Answer 6

Although your photo did not come through, I believe I was able to get the measurement you were wanting, which is the distance from the center of the hitch pin holes to the back of the closest part of the B&W Tow & Stow 2-Ball Mount - 2"…

view full answer...

Answer 7

From the center of the hitch ball to the rear hitch pin is 9.55" on the Weigh Safe 6" Drop Hitch item #WS46ZR. Additionally, it is 8.42" from the 2nd hitch pin to the center of the hitch ball.

view full answer...

Answer 8

Yes, it will Lyle. I just went out to the warehouse and took some measurements. The oblong hole where the hitch pin inserts is 1-7/8" - 3" behind the weld where the Weigh Safe Anti-Rattle Reducer Sleeve item #WS79ZR inserts. This will…

view full answer...

Answer 9

Hey Kody! I found an extremely detailed schematic diagram of the BulletProof Hitches 2-Ball Mount for 3" Hitch item #ED304 that I have attached below. It covers multiple dimensions of that hitch pin hole to the angled piece. If you have any…

view full answer...

Answer 10

The Curt hitch bar part #C55NR that you referenced doesn't have a listed weight capacity since a lot of that will be based on how it's installed. Since this is a 3 inch hitch opening the capacity is going to be very high so I wouldn't…

view full answer...

Answer 11

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 12

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Distance From Hitch Pin Hole to Vertical Adjustment Shaft on Fastway Ball Mount # FA49-00-5625

Product Page this Question was Asked From

Continue Researching