7-Way Trailer Wiring Kit Recommendation for 2020 Dodge Durango

Question

Question:

I have a 2020 Dodge Durango that does not have trailer wiring that I want to add a 7-way to. What should I get?

asked by: Dale

0

Expert Reply:

We have a very easy to install 7-way wiring kit that fits your 2020 Dodge Durango with the Tekonsha part # TK22113. This comes with everything needed for a plug and play install of a 7-way on your Durango!

expert reply by: Jameson C

0

Answer 1

I'd recommend the Curt Class III hitch, part #C13182 because of it's high capacity and the nice build and finish quality you'll find with a Curt hitch. Not to mention it's a heckuva lot less expensive than the OEM item. Keep in mind,…

view full answer...

Answer 2

The traditional wire colors for brake controller installation are white for ground, black for 12 volt power, red for stoplight switch, and blue for brake output. For more information on wiring in a brake controller check out the help article I…

view full answer...

Answer 3

As the Tekonsha #TK22113 is designed to fit a Dodge Durango up to 2018, we will not have a video of it on a 2020. This is due to the 2020 models not having the wires run under the dash, unfortunately. With that being said, to get a 7 way installed on…

view full answer...

Answer 4

I recommend the Draw-Tite Max-Frame Trailer Hitch Receiver part #DT38MR for the 2020 Dodge Durango that allows the knock out panel to be replaced when the hitch is not in use. I have attached an installation video on a 2019 Dodge Durango but the…

view full answer...

Answer 5

According to the install instructions for the Tekonsha 7-way part #TK22113 that fits your 2018 Dodge Durango the blue wire gets routed through the grommet in the floor on the driver side into the rear cargo area and then routed behind side cargo trim…

view full answer...

Answer 6

Yes, you are absolutely correct, the Tekonsha OEM Replacement Vehicle Wiring Harness with Brake Controller Adapter - 7 Way Trailer Connector #TK22113 will fit your 2020 Dodge Durango that does not currently have factory trailer wiring. It says…

view full answer...

Answer 7

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 8

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 9

The main difference between the Curt Trailer Hitch Receiver part #C13416 and the EcoHitch Hidden Trailer Hitch Receiver part #EH97FR is that the EcoHitch has a completely hidden cross tube whereas the Curt cross tube will be visible from the rear of…

view full answer...

Answer 10

Hi David! There are quite a few hitches offered for your 2026 Honda Odyssey, so I definitely understand wanting to know the differences. There are basically three styles available for you and I have them broken out below: Exposed Crosstube: etrailer…

view full answer...

Answer 11

Hey Ricardo! Yes, the Curt Trailer Hitch Receiver #C82RJ is the hitch Curt is working on for the new 2027 Telluride. This is a pre-order since Curt hasn't finished the design. It does not include wiring. The wiring harness for the 2027 is also up…

view full answer...

Answer 12

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

7-Way Trailer Wiring Kit Recommendation for 2020 Dodge Durango

Featured Help Information

Miscellaneous Media

Continue Researching