How to Remove Bearing Buddy Bearing Protector From Hub
Updated 09/18/2019 | Published 09/16/2019
Question:
I tried removing the bearing Buddy by tapping with a wood block just like the first three but this one separated leaving the insert still in the hub and the grease part came off. Is there a different way to get these out? These were brand new. I thought they were all one piece.
asked by: Gary I
Helpful Expert Reply:
The best way to remove a Bearing Buddy Bearing Protector like # BB2717 is pretty much what you've been doing. Because the fit inside the hub bore is pretty tight, you just have to take a rubber mallet (or wood block) and firmly tap it around the sides until it's unseated and loosened up enough to pull it out by hand. This process is briefly shown right at the beginning of the video I attached below.
If your Bearing Buddy came out in a couple of pieces it was likely damaged in the removal process. The unit should indeed be one single piece (not counting the rubber cover). When removing one just make sure you aren't hitting the unit too hard (but firm enough) and are alternating the contact point between each hit (left side, right side, top, etc).
Product Page this Question was Asked From
Bearing Buddy Bearing Protectors - Model 2717 - Chrome Plated - Qty 2
- Trailer Bearings Races Seals Caps
- Caps
- Bearing Protector Grease Cap
- 2.72 Inch
- 5200 lbs Axle
- 6000 lbs Axle
- 7000 lbs Axle
- Bearing Buddy
more information >
Featured Help Information
Miscellaneous Media
Continue Researching
- Search Results: rv water inlet
- Shop: Steel Spoke Trailer Wheel - 14" x 6" Rim - 5 on 4-1/2 - Galvanized Finish
- Search Results: dexter seal 10 36
- Search Results: 3 inch valve body rv waste valves
- Search Results: twist on waste valve
- Video: All About the B and B RV City Water Inlet
- Video: Review of the Omega LED RV Porch Light with Switch
- Shop: etrailer Electric Trailer Brakes - Self-Adjusting - 10" - Left/Right Hand Assemblies - 3.5K
- Video: Cleaning and Replacing Hubs and Bearings
- Search Results: 023~026~00
- Shop: Valterra Bladex Waste Valve Body for RV Black Water Tank - Aluminum Handle - 3" Diameter
- Shop: B&B RV City Water Inlet - Plastic Check Valve - Recessed Dish Mount - Polar White
- Shop: Karrier ST205/75R14 Radial Trailer Tire with 14" Galvanized Wheel - 5 on 4-1/2 - Load Range C
- Shop: B&B RV City Water Inlet for Flusher with Flange - Surface Mount - Plastic Valve - Polar White
- Shop: B&B RV City Water Inlet - Plastic Check Valve - Recessed Dish Mount - Black
- Q&A: Ways To Remove Broken Off Ring For Bearing Buddy Stuck In Trailer Hub
- Q&A: What is the Best Grease for Trailer Bearings
- Video: Feature Review LubriMatic LMX Industrial Strength Grease
- Article: Trailer Wiring Diagrams
- Shop: Trailer Hitch
- Q&A: What is the Difference Between a Class II and a Class III Hitch?
- Search Results: trailer hitch
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Shop: Trailer Wiring
- Q&A: Lug Nut Torque Chart for Trailer Wheels
- Search Results: trailer tires and wheels
- Video: Firestone Ride-Rite Air Bags with Easy Mount Compressor Feature Breakdown
- Q&A: Installation Time for Blue Ox BX1128 Flat Tow Base Plate Kit for 2016 Jeep Grand Cherokee
- Video: How to Choose a Trailer Brake Controller
- Shop: Suspension Enhancement
on Trailer Bearings Races Seals Caps
