Availability of 10,000 lb Axle Dexter Trailer Brake Assemblies

Question

Question:

Do you have a lower cost option for these brakes?

asked by: Tyler E

0

Expert Reply:

The only option we have for 10k axle rated Dexter electric brake assemblies is the part # 23-438-439 that you referenced. 10k trailer axles with drum brakes just aren't as popular as other options so there isn't as much competition for this size.

expert reply by: Jameson C

0

Answer 1

Since your trailer has Dexter 10k axles the correct hub/drum you need is the part #8-430-5UC3 which comes with bearings, races and seal. Since you need shoes and magnets it would be easiest to go with new assemblies altogether like with the part…

view full answer...

Answer 2

The Dexter Electric Brake Kit #23-450-451 are the brakes you will need for your 2019 Big Tex 22GN with the 10,000lb Dexter axles. These are sold per axle so you will need 2 sets to replace all 4 of your brake assemblies. They are also sold…

view full answer...

Answer 3

Since we know your 2015 Big Tex has Dexter 10k axles the brake assembly set you need for each of your 10k Dexter axles is the part #23-450-451. This set of left and right assemblies is exactly what your Dexter axles need and they are self adjusting…

view full answer...

Answer 4

When you replace your Brakes #23-450-451 it is a good idea to inspect the bearings at that time. The bearings and races will only need to be replaced if they are damaged or grooved. A visual inspection of the seal will tell you if it leaking or you…

view full answer...

Answer 5

The Dexter Electric Brake Kit #23-450-451 are the brakes you will need for your 2018 Big Tex 22GN with the 10,000lb Dexter axles. These are sold per axle so you will need 2 sets to replace all 4 of your brake assemblies. They are also sold…

view full answer...

Answer 6

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 7

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 8

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 9

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 10

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 11

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 12

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Availability of 10,000 lb Axle Dexter Trailer Brake Assemblies

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching