Shaft Dimensions for the 18-5/8" Replacement Awning Extension Rod for Solera Slide-Topper Awning

Question

Question:

Does this piece measure 3/4 inch hex

asked by: Ivor R

0

Expert Reply:

Yes, the Replacement Awning Extension Rod for Solera Slide-Topper Awning # LC3452072 that you referenced measures 3/4". I actually recently took this same measurement for another customer for the white version part # LC3452071 and I'm attaching the dimensional photo for you to reference.

expert reply by: Jon G

0

click to enlarge

Answer 1

Hi Tim! The PowerMax Wireless 50A RV Power Center and Distribution Panel - 60A DC Converter #PM77VR can definitely be mounted on its side. There is nothing inside this that would specifically need it to be mounted vertically, so you are good to go!…

view full answer...

Answer 2

It sounds like you're looking for the Replacement Awning Extension Rod for Solera Slide-Topper Awning part #LC3452071 for white or part #LC3452072 for black which measure 18-5/8" long.

view full answer...

Answer 3

I recommend replacing the Extension Rod for your slide topper. With your current rod being bent even if you were able to bend it back straight it will more easily bend in the future or could break. We have the following extension rods for the Solera…

view full answer...

Answer 4

Hey Steve, thanks for reaching out! The Replacement Extension Rod #LC3452072 will only work with Solera awnings, and we don't have an extension that will fit your A&E awning. We have some replacement arm kits, but if you're only wanting…

view full answer...

Answer 5

To retention your Solera RV Slide-Out Awning #LCV000168109 you'll want to extend the slide out and can then get on a ladder and get up to the arms. You'll disconnect the extension rod #LC3452072 from the arm and then can roll the arm 12 - 16…

view full answer...

Answer 6

The Replacement Awning Extension Rod for Solera Slide-Topper Awning item #LC3452072 (black) and item #LC3452071 (white) is going to be the closest we can get to 19" long. This is a 3/4" hex bar that is 18-5/8" long. This replaces the…

view full answer...

Answer 7

Mano, it's not Dometic but the Lippert #LC3452072 appears to be the exact same thing. This bar measures 18 5/8" and will work with brackets designed for hex shaped bars, like what's on your Dometic.

view full answer...

Answer 8

The reason why the extension rod of your Solera RV Slide-Out Awning #LCV000168107 is touching the corner flange piece is either because you have too large of an awning installed or the awning isn't centered on the slide out. If the tension…

view full answer...

Answer 9

For replacing the Drive Head #LC34FR and Idler Head #LC87FR on a Solera Slide Topper you will want to completely remove the slide topper from your RV/Camper. You will need to insert a pin into the end of the tube end cap(see image) to keep the…

view full answer...

Answer 10

The Replacement Bracket for pre-2019 Solera RV Slide-Out Awnings #LC2724411 is 7 inches long and the portion that attaches to the trailer is 2 inches tall.

view full answer...

Answer 11

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 12

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Shaft Dimensions for the 18-5/8" Replacement Awning Extension Rod for Solera Slide-Topper Awning

Products Featured in This Question

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching