Anti-Rattle Lock Recommendation for 2.5 inch Hitch and B and W Tow & Stow

Question

Question:

Will this threaded lock assembly work on my 2500HD Sierra with 2.5” receiver and bandw tow and stow hitch ?

asked by: Mike F

0

Expert Reply:

For the larger 2-1/2 inch hitch size the anti-rattle lock you'd want is the SilentACT Anti-Rattle Trailer Hitch Accessories Lock # SHP2082 which is compatible with the hollow shank of your B&W Tow & Stow 3-Ball Mount # BWTS20049B that you have.

expert reply by: Jameson C

0

Answer 1

I went out to our warehouse to take a look at the B&W Tow & Stow 3-Ball Mount #BWTS20048B and measured a distance of right at 5-1/2 inches from the bottom of the shank to the lowest point of the vertical adjustment post. I have attached an…

view full answer...

Answer 2

The B&W Tow & Stow #BWTS20048B has a distance from the center of the hitch pin hole to the end of the shaft of 4-1/2 inches for the nearest hole. The other hitch pin hole is 5-5/8 inches. I've attached a photo to assist.

view full answer...

Answer 3

It is actually not all that difficult to install or remove the Let's Go Aero anti-rattle hitch pin #SHP2082. In most cases you can reach in with a finger and pull out the spring and block portion. Otherwise a screwdriver would have short work of…

view full answer...

Answer 4

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 5

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 6

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 7

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 8

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 9

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 10

Hey Larry! Yes, the Onan Generator - QG 7000i Onboard RV Generator #CM44MR is capable of using a remote start. For a standard setup, you can use a switch like #CM86RR along with an extension harness #CM26RR. You can also use the EC-AGS+ Auto…

view full answer...

Answer 11

Hey Lauris! Is the Brinkley prepped for a generator or are you saying it has room for one? If it doesn't have some kind of generator prep you're going to need a lot of parts from Cummins to install #CM44MR. You will have to add a fuel tank,…

view full answer...

Answer 12

Hey Cindy, thanks for reaching out. We may have an extension that will work for you. It will help to know exactly how long of an extension you are needing as this will be one of the main deciding factors. Let me know how long you need it to be in the…

view full answer...

Anti-Rattle Lock Recommendation for 2.5 inch Hitch and B and W Tow & Stow

Products Featured in This Question

Continue Researching