Standard Trailer Lug Nut for Trailer with 13 inch Diameter Wheel

Question

Question:

I have a trailer that I need replacement lug nuts for. The tariler ihas a GVWR OF 2000LBS, 13X5 BOLT PATTERNRIMS ST175 - 80-13inch Load Star Trailer. Local auto stores have no help.

asked by: Dale J

1

Helpful Expert Reply:

The standard trailer lug nut is like the part # AM26NR which has a thread size of 1/2" - 20 and also has the standard 60 degree cone. I'd be shocked if your trailer needed something different.

expert reply by: Jameson C

1

Answer 1

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 2

Hey Matt, thanks for the pictures of your spindle dimensions. The bearing numbers you mentioned are correct so for a replacement hub/drum you'd need a 3,500 lb axle hub like the part #84546UC3-EZ.

view full answer...

Answer 3

Based on the measurements you provided you have #LM67048 inner bearings and #LM11949 outer bearings. There is only one hub that would fit with a 5 on 4-1/2 inch bolt pattern, which is the #AH15450ECOMP Trailer Hub Assembly. This is designed for…

view full answer...

Answer 4

Based off the measurements you provided, you've got a #84 spindle, so the correct bearings are the #L44649 and #L68149, and #RG06-050 grease seals. We typically try to put bearing numbers of popular manufacturers on the bearing pages but those…

view full answer...

Answer 5

Trailer Idler Hub Assembly #AKIHUB-545-35-K was designed to work with 13" to 17-1/2" wheels so it is not a good option for 8 inch trailer wheel #AM20028. We have a lot of hubs that fit 8 inch wheels and have a 5 on 4-1/2 bolt pattern but…

view full answer...

Answer 6

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 7

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 8

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 9

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 10

Hey Bryan, that's a good question. The pricing can definitely be misleading, but I wouldn't use it to judge the quality of the tire. A lot of that comes down to promotions, inventory, and whether you're looking at a tire by itself or…

view full answer...

Answer 11

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 12

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Standard Trailer Lug Nut for Trailer with 13 inch Diameter Wheel

Product Page this Question was Asked From

Continue Researching