Does Curt 7-Way/4-Way T-Connector Fit 1999 Ford F-150 with Factory 7-Way

Question

Question:

Will this harness work on a 1999 f150 with factory 7-pin

asked by: Patrick

1

Helpful Expert Reply:

Yes, the Curt T-Connector Vehicle Wiring Harness # C55774 uses the standard US Car Connector (see attached photo) which you should have on your 1999 Ford F-150 (behind your current connector). This connector will just plug into place.

expert reply by: Jon G

1

click to enlarge

Answer 1

The Ford Replacement OEM Tow Package Wiring Harness, 7-Way #118242 will upgrade your factory 4-way connector to a 7-way. You will also want the mounting bracket #PK-12711U to position your 7-way connector in a convenient location and keep dirt and…

view full answer...

Answer 2

We have a nice selection of custom trailer hitches available for the 2018 Ford F-150 that isn't equipped with the factory hitch. I specifically recommend the Curt Class IV Receiver Hitch #C26HR because it offers the highest capacity available…

view full answer...

Answer 3

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 4

Hey Rob! You can actually use either one, but my recommendation would be the Custom Underbed Installation Kit for B&W Companion 5th Wheel Trailer Hitches #BWGNRK1320-5W. B&W makes some of the best hitches available, and the Turnoverball is no…

view full answer...

Answer 5

Hey, Stephen! We got just what you need. Since you don't have a tow package, I'm not sure if you have a hitch on your 2025 Ford Ranger so I'll include one just in case. Draw-Tite Max-Frame Trailer Hitch Receiver Part #DT35PR Curt…

view full answer...

Answer 6

Hey Kim, thanks for reaching out. The Firestone Ride-Rite Air Bags with Easy Mount Compressor #F24XV do fit your 2020 Ram 2500 with rear coil springs, but the hang-up is the under-bed gooseneck hitch. On your truck, the air bag brackets and the…

view full answer...

Answer 7

Hey David, welcome back. To add a 4-way connector to your 2025 Kia Sportage PHEV, you'll want the Curt item #C99DR. It connects directly behind the rear tail lights and there isn't a way to connect it to a tow package. It will not control a…

view full answer...

Answer 8

Hey Randy! For the OEM prep package you'll need to reach out to a Ram dealer, but I can help you out with an underbed system for your 2026 Ram 2500 if you aren't dead-set on getting the exact same as the OEM. The closest we have for your…

view full answer...

Answer 9

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 10

You can use a 7-Way and 4-Way connector at the same time just as long as you are not overloading the light circuits. If your camper has a lot of outside lights like running lights, and brake/stop/turn lights then the lights that perform the same…

view full answer...

Answer 11

Thanks for reaching out, Jack! What I recommend using is the Curt Adapter #C57672 and securing it to your vehicle with the No-Drill Bracket #18136. This gives you the ability to seamlessly use either the 4-Way or 7-Way connection but doesn't…

view full answer...

Does Curt 7-Way/4-Way T-Connector Fit 1999 Ford F-150 with Factory 7-Way

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching