Torque Spec For The B and W Hitch Ball BWHB94004

Question

Question:

what are the torque spec for this hitch ball

asked by: Brian

0

Expert Reply:

The Tech at B&W says the hitch ball part # BWHB94004 should tightened to 120 ft lbs with a 2-15/16" wrench.

expert reply by: Heather A

0

Answer 1

Stan, there aren't any benefits to using a higher rated ball like the 2-5/16" Hitch Ball #BWHB94004 you were looking at, but there also aren't any disadvantages either. The only thing you'd need to take into consideration is that…

view full answer...

Answer 2

The Curt trailer hitch balls are all made in China. Many trailer hitch receivers too are made outside the U.S. but Curt does manufacture their hitches stateside. The 2-5/16-inch hitch ball you referenced, Curt #C40030, has a 15K gross trailer weight…

view full answer...

Answer 3

The Fulton Round, Snap-Ring Swivel Marine Jack #FTJ120W0301 will work in place of your 1,000 lb Atwood snap-on jack as long as the bracket that is on the jack matches up with the dimensions in the attached picture. If they don't match up then let…

view full answer...

Answer 4

This is a great question that there isn't exactly a great answer for. Hitch extenders not only put the weight further away from the hitch which would increase the leverage on the hitch, but they also add movement to the assembly which will…

view full answer...

Answer 5

Hey BK, thanks for reaching out! Most hitch pins don't have a weight rating, but the Gen-Y Hitch Pin and Clip #325-GH-099 does, and that's 32,000 lb towing. This will be the same whether you're using a hitch adapter or not. For a locking…

view full answer...

Answer 6

One thing to note when using a hitch extender like the etrailer, #e88YR, is that the tongue weight and towing capacity of your trailer hitch will be reduced by 50 percent due to the increased leverage that is placed on your trailer hitch from your…

view full answer...

Answer 7

Hey Andrew, yes the Redarc Tow Pro Liberty part #RED72CR is a fit for your 2015 Toyota Tundra with the factory tow package and is a really great option. There is a port under your dash that the included custom harness is designed to fit. It only puts…

view full answer...

Answer 8

Hey Joe, while I don't know what brake controller you have you should be able to unplug it from the back of the brake controller and that would accomplish what you are wanting. What brake controller do you have?

view full answer...

Answer 9

The height of the Curt RockerBall from the base that sits upon the ball mount to the top of the ball is as follows: - 2-5/16 inch ball with 1 inch diameter shank, #C82KR is 4.607 inches - 2-5/16 inch ball with 1-1/4 inch diameter shank, #C29FR is…

view full answer...

Answer 10

The B&W 2-5/16" Hitch Ball - 1-1/4" Diameter x 2-1/2" Long Shank #BWHB94004 has a nut that is the traditional socket size of 1-7/8 inch and has fine threads that are 12 threads per inch to fit that 1-1/4 diameter shank.

view full answer...

Answer 11

A chrome finish ball #C40036 is going to look good but it will not be corrosion resistant. A ball with a machine finish like #C40087 , is going to have about the same corrosion resistance. In terms of performance they will wear at about the same rate…

view full answer...

Torque Spec For The B and W Hitch Ball BWHB94004

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching