Availability of 3 and 4 Long RV Sewer Nipples with 3 MPT End

Question

Question:

Do you have 3” MPT 3” long and 4” long

asked by: Nelson J

0

Expert Reply:

Yes, for a 3 inch long RV sewer nipple with 3 inch MPT ends we have the Valterra # T3503 and for a 4 inch length we have the Valterra # T3504. We do also have thread tape # A05-0265 if needed.

Both sewer line nipples feature a 3 inch MPT thread at each end. I have attached a couple short video reviews that you can check out as well.

expert reply by: Chris R

0

Answer 1

We do carry toilet floor flanges for RV's. We have the LaSalle Bristol Toilet Floor Flange for RV #3446336343 which has a 3" MPT end that threads into your RV's black-water system and the LaSalle Bristol Toilet Floor Flange for RV…

view full answer...

Answer 2

The threaded part of Replacement RV Toilet Floor Flange - 3" MPT Item #T05-0782 is 13/16 inches tall. I have included a couple of pictures show several measurements of this part for you.

view full answer...

Answer 3

I reached out to Valterra for the dimensions of the Valterra RV Toilet Floor Gasket with Hold Down Bolts #Q23653VP, and they sent me the accompanying dimensional diagram. It has an outer diameter of 4-3/4", an inner diameter of 3-1/4" and…

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 7

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 8

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 9

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 10

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 11

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 12

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Availability of 3 and 4 Long RV Sewer Nipples with 3 MPT End

Products Featured in This Question

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching