How To Install the Redline Trailer Vent # WHMAV2-WAVT2 on an Enclosed Trailer
Updated 01/17/2012 | Published 01/14/2012
Products Featured in This Question
Question:
I was curious on part:Redline Enclosed Trailer Parts - WHMAV2-WAVT2 If you had a video of how to install this on a 12x16 enclosed trailer? Thanks!
asked by: Steve
Expert Reply:
I do not have an installation video on the Redline Trailer Vent, part # WHMAV2-WAVT2, but I can help you with the installation. The tools you will need are a caulk gun, drill, a 3-inch hole saw, a 3/16-inch drill bit, and a flat-tip screwdriver. The other parts you will need I have listed below in the instructions.
The # WHMAV2-WAVT2 vent is two pieces. The # WAVT2 is the 3 inch round interior vent that will need to be installed in a 3 inch diameter hole on your trailer. You will need to cut a 3 inch diameter opening on you trailer and insert the vent through the hole. Drill three 3/16-inch holes where the screws will go. I would recommend to put a sealant like # 0160297, around the lip of the round vent before attaching to the trailer with three of the # 30587 wood screws.
The # WHMAV2 will install on the exterior of the trailer and will insert into the 3 inch round vent of the # WAVT2. You can position the slotted vents on the # WHMAV2 for the best airflow and drill six 3/16-inch holes where the screws will go. Also, put some sealant on the edges of the vent before attaching to the trailer with six of the # 31071 sheet metal screws.
That is all that is necessary to install the trailer vent on your enclosed trailer.
Product Page this Question was Asked From
2-Piece Exterior Wall Vent for Enclosed Trailers - Polypropylene - 3" Diameter Hole - White
- RV Vents and Fans
- Vent
- Wall Vent
- No Fan
- Plastic
- White
- Redline
more information >
Continue Researching
- Search Results: 0160297
- Search Results: accessories and parts
- Search Results: sealant
- Search Results: 31071
- Search Results: screws
- Q&A: Vent Solution for Trailer Tongue Box that Holds In Moisture
- Video: Replacement Round Interior Trailer Vent for 3" Diameter Hole: The Breakdown
- Video: Replacement Exterior Half-Moon Trailer Vent for 3" Diameter Hole Feature Review
- Shop: Zinc Sheet Metal Screw - 8 x 3/4" Indented Hex Washer Head - Hex Slotted Drive
- Shop: Alpha Systems 1010 Non-Sag Sealant for RVs - White - 10.3 oz - Qty 1
- Shop: Rock River Silicone Sealant - 9.8 Fl-Oz - White
- Shop: Replacement Exterior Half-Moon Trailer Vent for 3" Diameter Hole - White
- Shop: Hook and Keeper for Enclosed Trailer - 6" Hook - Polar White
- Shop: Buyers Products Hook and Keeper for Enclosed Trailer Door - Stainless Steel - 6" Hook
- Shop: 2-Piece Exterior Wall Vent for Enclosed Trailers - Polypropylene - 3" Diameter Hole - Black
- Search Results: hole saw
- Q&A: Adding A Rooftop A/C Unit To An Enclosed Trailer
- Search Results: trailer vent
- Q&A: How Does Enclosed Trailer Vent Keep Rain Out of Trailer?
- Q&A: Installation of Redline 2-Piece Polypropylene Trailer Vent # HMAV2-AVT2
- Q&A: Installation Hardware for Trailer Vent HMAV2-AVT2
- Q&A: Can an AC be Installed on a 14x7 Utility Trailer?
- Q&A: Side Wall Vent Recommendation for an Enclosed Trailer for Maximum Air Flow
- Article: Trailer Wiring Diagrams
- Article: How to Measure for Trailer Hitch Drop
- Article: Trailer Lighting Requirements
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Article: Types of Trailer Hitches: How and Why to Use Each
- Article: Ball Mount Basics: Weight Capacity, Class, and Size
- Article: How to Install E-Track in 3 Easy Steps