Where on Axle Should Spring Seats Be Welded On

Question

Question:

Hi Folks, I received your 2 3/8 dia axles that I need to weld the spring saddles in place. My question is the tubes are bent to account for loading so the wheels run true. Does the axle bend go up or down?

asked by: Jamie

1

Helpful Expert Reply:

The bend in an axle (the top of the arch) should be at the top of the axle so that as the trailer load is placed on the axle it flattens out. The spring seats # TRSS238 should be welded to the underside as shown in the linked diagram.

expert reply by: Adam R

1

click to enlarge

Answer 1

For your upgrade in trailer suspension on your triple axle Weekend Warrior toy hauler I recommend the E-Z Flex Triple Axle Suspension Kit with 7-3/4" Equalizers #K71-657-00. This kit comes with all the equalizers and hardware you need. Then you…

view full answer...

Answer 2

It is highly recommended that the spring seat be at minimum tack welded to the axle. There have been issues that have resulted from the seat not be welded to the axle. If you do not have access to a welder, I recommend taking the trailer to a local…

view full answer...

Answer 3

Appreciate the photo, and what that shows is you have a 5,200 lb axle that is 86-1/2 inches hub face to hub face with a spring center to spring center measurement of 68-1/2 inches. We do have a replacement with that capacity and the correct length,…

view full answer...

Answer 4

You have to be careful if you lubricate electric trailer brakes such as #23-468. You cannot get any grease on the pads or on the inside of the drum because that will have a negative impact on brake performance. The magnet arm and the shoes pivot at a…

view full answer...

Answer 5

We do have the correct replacement bushing and wet bolt for your E-Z Flex Heavy Duty Rubber Suspension System by Dexter Axle #K71-652-00, which I'll list out for you to make it easy to click and order: - Bronze Bushing #D014-077-00 (Quantity of…

view full answer...

Answer 6

Yes when you do an over-under kit you have to weld the seats to the axle for it to be installed properly. It is recommended to tack weld the new spring seats into place but a complete weld job is not required when installing the over-under conversion…

view full answer...

Answer 7

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 8

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 9

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 10

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 11

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 12

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Where on Axle Should Spring Seats Be Welded On

Product Page this Question was Asked From

Continue Researching