Size of Crank Fitting on Lippert Components Spare Tire Winch LC159056

Question

Question:

Im about to order the lippert spare tire winch and extension. I already have the Bal-C stabilizer Jacks on my trailer and their crank handle which I believe is 3/4. Do you know if this is pretty standard and would work with the lippert extension?

asked by: Jerry A

0

Expert Reply:

Lippert Components Spare Tire Winch # LC159056 has a 1/2-inch round crank fitting and uses Replacement Crank Extension # LC1315411. One end of this part has a 3/4-inch hex shape to mate with a crank handle.

If you have a crank handle with a 3/4-inch hex fitting it should work fine.

expert reply by: Adam R

0

click to enlarge

Answer 1

Yes, the Pollak Replacement 7-Pole, RV-Style Trailer Connector Socket #PK11893-11933 is still available. This is the same as the PA66-MD40 which fits your 2007 Dodge Dakota. For your spare time mounting cable assembly you will want to contact a local…

view full answer...

Answer 2

If you check out the diagram I attached of the side of the Lippert Components Spare Tire Winch #LC159056 that mounts you can see that the distance between the mounting hole locations is 5-1/4" on center. I reached out to my contact at Lippert…

view full answer...

Answer 3

Thanks for the picture! I checked with Progressive Dynamics the replacement power converter you need for your Parallax Series 7300 Model 7345 is the Replacement Converter for Parallax/Magnetek or WFCO RV Power Centers - 45 Amp item #PD4645V.

view full answer...

Answer 4

Hey Mike! Tires like the Maxxis ST225/75R15 Radial Tire #MXS77FR can replace the 8.75-16.5 tires on your trailer. Going to a smaller size is not really a concern as long as the tires have a high enough capacity to handle your trailer. The Maxxis…

view full answer...

Answer 5

Hey Charles, sounds like you have the Tamarack ST225/75R15 LRE trailer tire part #TA46AR on your 2024 Arctic Wolf which is a very solid trailer tire. This tire even has a 2 year roadside assistance program and a 5 year warranty so I think you can…

view full answer...

Answer 6

Hello John, There isn’t a specific weight rating listed for the Replacement Crank Extension for Lippert Spare Tire Winch Assemblies - 35-1/2" #LC1315411. However, most Lippert spare tire winches are rated to handle 100 lbs or more, which is more…

view full answer...

Answer 7

The crank handle for the Lippert Components Spare Tire Winch with Offset Cable item #LC159056, is Replacement Crank Extension for Lippert Spare Tire Winch Assemblies - 35-1/2" item #LC1315411. The Spare Tire Winch item #LC159056 has a 1/2-inch…

view full answer...

Answer 8

There is no way to lock the Lippert RV Spare Tire Carrier with Winch #LC159041 as it ships from the factory. You would need to weld on a tab which would allow you to use a Pin #37201211 by drilling a hole through the tab and shaft for the winch. We…

view full answer...

Answer 9

Looking at the BAL Retract-A-Spare it has a much different design than the Lippert Spare Tire Winch #LC159056 you found. You may be able to mount the new winch so it will still work on your trailer but as we do not have both the products here with…

view full answer...

Answer 10

Hello Don, thanks for reaching out. Yes, there is an air bag kit that will work on your 2001 Ford F250 with the B&W GNRH1108 gooseneck hitch. For that I recommend the following: - Air Lift LoadLifter 5000 Air Helper Springs - Rear Axle #AL57298…

view full answer...

Size of Crank Fitting on Lippert Components Spare Tire Winch LC159056

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching