Which Valterra Bladex Waste Valve Will Fit Schedule 40 PVC Pipe 3 inch Diameter

Question

Question:

Will a T40B fit on 3inch sch. 40 plastic pipe?

asked by: Robby S

0

Expert Reply:

Schedule 40, 3 inch PVC pipe has an outer diameter of 3.5 inches and an inner diameter of 3 inches. The Valterra Bladex Waste Valve # T40B you referenced is designed to fit OVER a 3 inch diameter pipe so what you'd need is the spigot version to fit into your 3 inch pipe like # T40A.

expert reply by: Jameson C

0

Answer 1

You can do that, however the mounting holes on #T1005 are a bit too close together, and won't properly mount to the Valterra Bladex Waste Valve for RV Black Water Tank #T40. Instead, I recommend using the LaSalle Bristol RV Sewer Slip Hub with…

view full answer...

Answer 2

Hi Joe, So you just need to know if the valve you are replacing slid over your pipe or into your pipe, and I'll go over how for you. If both ends of your waste valve slid into your sewer pipe you will need the Valterra Bladex Waste Valve for RV…

view full answer...

Answer 3

The Camco Dual Flush Adapter #CAM39072 is going to mounted pretty far from the opposite end of the holding tank so you would need a good amount of water pressure to effectively rinse all areas of the tank. It may not be enough to clear out clogs. For…

view full answer...

Answer 4

Since the valves are plastic welded to the sewer pipe you'll have to cut off what you have and install a new one. So you could use the Valterra Waste Valve for RV Black Water Tank - 3" Spigot to 3" Lug #T50A which you'd use the…

view full answer...

Answer 5

Hey Tav, the most "rugged" waste valve we have is going to be the Valterra Bladex Waste Valve for RV Black Water Tank #T40B. Valterra makes pretty good quality and durable products, so I'd recommend sticking with them.

view full answer...

Answer 6

The main difference between the Curt A30 5th Wheel Trailer Hitch #C16070 and Curt PowerRide 5th Wheel Trailer Hitch #C36WR for your 2020 Chevrolet Silverado 3500 Long Bed is the Wear Plates #C52WR. These wear plates for the PowerRide remove the need…

view full answer...

Answer 7

According to Curt, you never want to operate your PowerRide #C22ER fifth wheel hitch without the integrated lube plates installed. I am not sure what would have caused the screws to shear, but they are replaceable. We have #C52WR which comes with 2…

view full answer...

Answer 8

I recommend using the B&W Companion OEM 5th Wheel Hitch #BWRVK3715 for your 2024 GMC Sierra 3500 with the in bed factory prep/puck system. This hitch is made in the USA and B&W has great attention to detail. While the PowerRide #C36WR looks…

view full answer...

Answer 9

Hey Steve, Yes, a lube plate like the Curt #16721 can be used with the Curt PowerRide 5th Wheel Trailer Hitch #C48BR. If your wear plates do get worn out you can replace them with part #C52WR.

view full answer...

Answer 10

Personally I prefer the B&W Companion OEM 5th Wheel Hitch #BWRVK3305 over the Curt PowerRide 5th Wheel Trailer Hitch #C48BR. With that said the Curt is rated for 30,000lbs while the B&W is only rated up to 25,000lbs so if you need to tow a…

view full answer...

Answer 11

We do carry the Replacement Wear Plates #C52WR for the Curt PowerRide 5th Wheel Trailer Hitch #C48BR that fits your 2022 Ford F-350 long bed with the factory prep/puck system. Unfortunately, there is no estimated life span for these as there are to…

view full answer...

Answer 12

Great choice, Rodger! The 30K Curt PowerRide #C74BR uses wear plates that eliminate the need to add grease or use a lube plate. When the wear plates get worn down enough you'll use the Replacement Wear Plates #C52WR to keep your pin box from…

view full answer...

Which Valterra Bladex Waste Valve Will Fit Schedule 40 PVC Pipe 3 inch Diameter

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching