Recplement for the Shelby A-Frame Coupler 5104

Question

Question:

Hello need replacement coupler for a Shelby 5104 2006 2 5/16 ball do you a a suggestion?

asked by: Damon

1

Helpful Expert Reply:

The best replacement for your Shelby A-Frame Coupler 5104 is the A-Frame Trailer Coupler part # CA-5400-B. The Shelby 5104 fits a standard 50-degree a-frame, has a 13,000 lb weight capacity, and uses a 2-5/16" hitch ball. The A-Frame Trailer Coupler also fits a standard 50-degree a-frame and uses a 2-5/16" hitch ball but has a 14,000 lb weight capacity. In order to install this trailer coupler you will need to cut the old one off and weld the new one on.

In order to protect your trailer while not in use, I recommend using the Master Lock Trailer Coupler Lock part # ML389DAT.

expert reply by: Conner L

1

Answer 1

The tongue weight capacity of the A-Frame Trailer Coupler #CA-5400-B that you referenced is 2,100 lbs. The overall trailer weight capacity for the coupler is 14,000 lbs.

view full answer...

Answer 2

The Dexter "8-248" is a hub assembly for 3,500 lb axles that uses an L68149 inner bearing and a L44649 outer bearing. This hub assembly was offered in both 5 on 4-1/2" and 5 on 4-3/4" bolt patterns therefore you would need to…

view full answer...

Answer 3

Thanks for following up with the photo. I see that you have size 225/75/15 tires with the 6 on 5-1/2 inch bolt pattern. We do not have the specific wheels you have, but we do have similar options. If you want the aluminum wheel with the tire…

view full answer...

Answer 4

Hey Bill! I went to inTech's website and we do not have an exact replacement for their coupler but we have something that will work. It's the Demco 50-Degree A-Frame Trailer Coupler w/ Jack Hole and Anchors item #DM16680-52. The Demco item…

view full answer...

Answer 5

Hey Stuart, unfortunately weight distribution systems do make some odd noises. Friction does a great job as a way to reduce sway but it does make a lot of noise. So with that said the friction in a weight distribution system is not intended to be…

view full answer...

Answer 6

I would use a protractor, see photo, place the protractor on the edge of the inside of one side of the trailer frame and the other inside edge of the trailer frame should be parallel with the 50 degree line on the protractor. Another way to verify…

view full answer...

Answer 7

Hey Nicholas. In order to get you a set of replacement hubs I'll need to know the part numbers stamped into the sides of the bearings on yours and your lug nut pattern. The only way a picture of your spindle is going to help me is if you have…

view full answer...

Answer 8

For whatever reason, some F-150 models will have the plug in the dash for the brake controller, but the 12 volt power feed to that connector hasn't been connected. You may need to add a 30A fuse in the distribution box under the hood, in location…

view full answer...

Answer 9

We offer a plug and play pigtail for your 1999 Chevy Silverado and your Tekonsha Primus IQ brake controller. The part you are looking for is #3025-P. The connection is under the dash on the driver side near the pedals. Just mount the controller and…

view full answer...

Answer 10

Hello Brandon, thanks for reaching out. The Replacement Left/Curb Side Leg for etrailer and Ram Hydraulic Jack #e63VV is intended to be used with the #e43VV power unit and #e73VV. The legs are designed to be used in tandem, but they can be used for…

view full answer...

Answer 11

Hey Ed, we can help but we don't have repair kits for the Shelby A-Frame coupler you have. Best option would be to replace the coupler like with the Fulton A-Frame Coupler part #FE443050303 which also has a 2-5/16 inch ball size. We do not carry…

view full answer...

Recplement for the Shelby A-Frame Coupler 5104

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching