Stainless Steel T-Strap Hinge for Side and Rear Trailer Doors

Question

Question:

Are these hinges stainless steel?

asked by: Jeff G

0

Expert Reply:

Polar T-Strap Hinge for Side and Rear Trailer Doors # PLR3416 is galvanized (zinc-plated) steel but not stainless steel. The zinc coating helps resist corrosion. For a similar hinge that is stainless steel we offer Polar part # PLR3416-SS.

expert reply by: Adam R

0

Answer 1

It looks like the closest thing that we have to that design is the Square Corner T-Strap Hinge w/ Reverse Bracket #PLR4040, but if that doesn't work we do have a wide variety of other hinge straps that may work for your application like the part…

view full answer...

Answer 2

Based on your picture it appears your trailer currently uses some screws like the 1" Long Black Torx Wall Liner Screw #WLS100. I do recommend verifying the correct bolts needed with the trailer manufacturer as the T-Strap Hinge #PLR2008-SSP you…

view full answer...

Answer 3

I do have an option for you but the handles included with the Cam-Action Lockable Door Latch Kits like part #PLR658-SSP must be welded to the pole as there are no other options to attach them. If you can get away with a 55" long pipe then you…

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

Hey Bryan, that's a good question. The pricing can definitely be misleading, but I wouldn't use it to judge the quality of the tire. A lot of that comes down to promotions, inventory, and whether you're looking at a tire by itself or…

view full answer...

Answer 7

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 8

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 9

The 5.30-12 tires, being wider, are going to make more contact with the road. This means that the noise, and heat build up will be higher than a 4.80-12 tire but the rolling resistance will actually be less because the tire is larger diameter. The…

view full answer...

Answer 10

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 11

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 12

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Stainless Steel T-Strap Hinge for Side and Rear Trailer Doors

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching