Parts Needed to Add a 7-Way and 4-Way to Rear of 2018 Ford F-150

Question

Question:

I have a 2018 f150 stx that has a 4 pin connector on it. Do you guys make a plug and play connector to have both the 7 pin and pin connectors?

asked by: Cody B

0

Expert Reply:

The first thing you'd need is the 7-way kit part # 118283 which will plug into the trailer wiring port you have at the rear of your truck. And then to convert that to a 7-way and 4-way you'd replace the included socket of this kit with the part # 74682 and you'd have a fully functional 7-way and 4-way for your truck.

expert reply by: Jameson C

0

Answer 1

Where to start with your wiring harness depends on what available connectors you have under the bumper of your 2020 Ford F-150 and also what trailer connector you're looking to add on your truck. If your truck already has the square shaped…

view full answer...

Answer 2

The Reese Multi-Plug Wiring Harness #74682 is meant more for replacing or upgrading a current 7-Way connector on a 2018 Ford F-150 right at the round US Car Connector. For your rectangular connector that you found you can use part #118283 instead.…

view full answer...

Answer 3

When it comes to removing the 7-way on your 1999 Ford F-150, there should be a grey locking clip like what is in the picture that I have attached. You'll just need to use a screwdriver to push that clip back slightly and slide it off. Once that…

view full answer...

Answer 4

For your 2018 Ford F-150 that has a factory 7-way we have the Reese Multi Plug Harness part #74682 which will replace your current 7-way and give you one that also has a 4-way harness attached to it. This will allow you to tow trailers with both…

view full answer...

Answer 5

If you have the factory 4-way, then you simply need the Replacement OEM Wiring Harness for Ford F-150 #C56110. If you have the factory 7-way then I recommend the Reese Multi-Plug Wiring Harness for Factory Tow Package - 7-Way and 4-Way Flat Trailer…

view full answer...

Answer 6

You are on the right track, your 2006 Ford F-150 XLT should be wired for a trailer. I went out and looked at my boss' 2005 Ford F-150 XLT which has the same wiring setup as your 2006 Ford F-150 and I took some pictures to show you where the…

view full answer...

Answer 7

When installing towing mirrors on your 2022 Ford F-150 Supercrew I recommend The K-Source Snap & Zap Custom Towing Mirrors - Snap On - Driver and Passenger Side #KS69NQ. These mirrors have an overall length of 16-1/2 inches. They have an easy,…

view full answer...

Answer 8

When a vehicle manufacturer states that chains cannot be used it is generally because there is a potential clearance issue between the inner sidewalls and vehicle components. However, in some places chains or cables are required by law. Since a…

view full answer...

Answer 9

Some vehicles can use tire chains only on specific tire sizes and/or only on one of the two axles, and this is determined by the auto maker. Other vehicles can use only a certain type of chain, such as low-profile S-Class chains, due to limited…

view full answer...

Answer 10

Hi there Brian; we have both snow tire chains and cables that fit 275-65/18 tires, though you definitely want to check your owner's manual to see if they are okay to use on your truck. I'm not sure why the dealer would say cables instead of…

view full answer...

Answer 11

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 12

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Parts Needed to Add a 7-Way and 4-Way to Rear of 2018 Ford F-150

Featured Help Information

Miscellaneous Media

Continue Researching