Height Measurements of Erickson Beg Bed Load Extender

Question

Question:

Please provide the height adjustments for Erikson EM07600. I would like to know the dimension from the center of the receiver hole to the top of the load cross bar for each of the three height settings. Thank You

asked by: Tom

1

Helpful Expert Reply:

The Big Bed load extender, part # EM07600, has three height settings in 1 inch increments. I went out to the warehouse and measured from the center of the hitch pin hole myself and they're about 17-1/8, 18/-1/8, and 19-1/8 inches to the top of the load bar.

expert reply by: Charles S

1

Answer 1

To secure the Flint Hill Goods Truck Bed Extender #FHG89ZR and keep it stable I recommend using the Anti-Rattle Trailer Hitch Receiver Lock #63232. This not only has a locking hitch pin to keep the extender secured to your vehicle, but it also has a…

view full answer...

Answer 2

Currently the only truck bed extenders we carry are going to be for a 2" receiver like the Erickson Big Bed Load Extender #EM07600. We do have a Titan Hitch Box Extension #RP45018 which you can use to have a custom made extender. This 41"…

view full answer...

Answer 3

The Erickson Big Bed Load Extender, #EM07600, measures 49-1/2 inches from the hitch pin hole to the outer edge of the upright. I have included a picture to illustrate this measurement. To determine exactly how far the extender, #EM07600, will extend…

view full answer...

Answer 4

The Erickson Big Bed Load Extender #EM07600 has crossbars which are 48-1/2" when in use, and that dimension does not include the wings - or tie-down points - at the end of the crossbars. The 48-1/2" is usable space, so your 4' wide…

view full answer...

Answer 5

The length of the truck bed extenders like the Erickson Big Bed Load Extender for 2" Hitches part #EM07600 are not adjustable. That said, all you would need to do is move the load away from the cab in order for it to rest on both the bed floor…

view full answer...

Answer 6

Hi Carlos, A hitch extender could be used with the Erickson Big Bed Load Extender for 2" Hitches #EM07600, it's just not recommended because you'd be cutting the capacity in half and putting a lot of leverage on the hitch. I recommend…

view full answer...

Answer 7

The lowest setting of the Erikson Big Bed Load Extender #EM07600 is 18" in height while the lowest setting of the Yakima LongArm Truck Bed Load Extender #Y01149 is measured at 17" high. That will still bring you at an inch higher than your…

view full answer...

Answer 8

According to my Erickson representative, their Big Bed Load Extender, part #EM07600 is 48-3/4 inches long, measured from the hitch pin hole to the rear surface of the upright, as shown in the provided photo. If you click the provided link, you can…

view full answer...

Answer 9

Yes, I have recommend load extenders such as #EM07600 for cars, trucks, vans, and SUVs. Sometimes it is just the right tool for the job! Once installed in the hitch the minimum height is 16 inches. If you measure from the top of the receiver opening…

view full answer...

Answer 10

The anti-rattle adapter I recommend is the No-Rattle Trailer Hitch Wedge, part #MPG908. This will work for 1-1/4 inch and 2 inch receivers and is designed to insert into the small gap that may exist on your receiver. You then tighten it up after it…

view full answer...

Answer 11

Yes the Malone Anti-Rattle HitchLock System Item #MPG908 will fit the Thule EasyFold XT part #TH903202 which does have an anti-rattle hitch pin. It will pull the rack a little tighter to the hitch tube.

view full answer...

Answer 12

The 400 lb limit would be for bed distributed loads. Basically, if what you are carrying weighs less than 400 lbs the Erickson Big Bed Load Extender #EM07600 that you referenced would work for you. Check out the review video I attached for this…

view full answer...

Height Measurements of Erickson Beg Bed Load Extender

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching