Polar Paddle Handle Locking Latch w/ Release Keyed Alike Option

Question

Question:

If I was to purchase 6 of the items above will they all be keyed the same or would it be six deferent keys?

asked by: Allen

0

Expert Reply:

The Paddle Handle Locking Latch w/ Release - 5-1/2" Long x 4-1/4" Wide - Steel # PLR5115 are not guaranteed to be keyed alike. I recommend using the Replacement Cam Lock Cylinder for RVs # 295-000003 to get your keyed alike option, but you do need to select keyed alike from the drop down on the product page.

expert reply by: Jason S

0

Answer 1

For a similar latch that can be keyed alike you will need to use the Global Link RV Entry Door Locking Latch Kit part #295-000002 which installs in a 2-1/2" wide x 3-1/2" tall to 3" wide x 4" tall cutout on a door 1-1/4" to…

view full answer...

Answer 2

I attached a couple pictures that show how flush latches like the part #PLR5115 that you referenced install. One shows the cutout and the other shows how the latch fits into it. You'd drill holes through the flange and door and use hardware that…

view full answer...

Answer 3

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 6

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 7

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 8

Trailer wheel bearings are specific to the spindle that is installed on the axle that is on your trailer. You will need to safely support the trailer, remove the wheel and tire, remove the grease cap, remove the cotter pin and washer that secures the…

view full answer...

Answer 9

The 5.30-12 tires, being wider, are going to make more contact with the road. This means that the noise, and heat build up will be higher than a 4.80-12 tire but the rolling resistance will actually be less because the tire is larger diameter. The…

view full answer...

Answer 10

To determine the size of the brake assemblies you need you have to measure the depth and width of the hub drum on the axle like what you see in the picture I attached. The most common size is 2-1/4 inch wide like the #T4071600-500 that you…

view full answer...

Answer 11

The three most common lug stud sizes for a trailer are 1/2"-20, 9/16"-18, and 5/8"-18. In order to make sure you get the correct lug nuts you need to measure the lug studs on the trailer now as we have no way to look this up for…

view full answer...

Answer 12

That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…

view full answer...

Polar Paddle Handle Locking Latch w/ Release Keyed Alike Option

Products Referenced in This Question

Product Page this Question was Asked From

Continue Researching