Can the Factory Trailer Hitch on a 2018 Toyota Tundra be Replaced
Updated 10/31/2018 | Published 10/30/2018
Question:
I want to replace a damaged factory receiver on my 2018 Toyota Tundra. Is this your best match?
asked by: Josh
Expert Reply:
The only trailer hitch receiver we have that will work on models equipped with a class III factory trailer hitch is the TorkLift SuperHitch Hero Trailer Hitch Receiver part # TLT1300H. If you have the class IV factory trailer hitch then we would not have any trailer hitch receivers for you.
If you are unsure whether or not you have a class III or class IV factory trailer hitch then you can take a look at the safety chain loops. If they are vertical then you have a class III but if they are horizontal then you have a class IV. The Draw-Tite Ultra Frame Trailer Hitch Receiver part # 41935 unfortunately does not fit model with the factory trailer hitch.
If you were to remove the factory trailer hitch, the aftermarket trailer hitch still would not fit as the factory trailer hitch receiver is integrated into the rear bumper and the aftermarket trailer hitch is not.
Continue Researching
- Search Results: trailer hitch
- Shop: Trailer Hitch
- Search Results: trailer wiring
- Search Results: 7 way flat
- Search Results: gen y torsion
- Shop: Trailer Wiring
- Search Results: hitch fabrication parts
- Video: Review of Patriot Hitches Trailer Hitch Ball Mount - 3 Ball Mount Stacked Receiver 30K - PH28NR
- Shop: Curt Trailer Hitch Receiver - Custom Fit - Class V Commercial Duty - 2-1/2"
- Shop: TorkLift SuperHitch Magnum Trailer Hitch Receiver - Custom Fit - Class V - 2-1/2" and 2"
- Shop: BTBRV Magnetic Hitch Receiver Reducer Set - 3" to 2-1/2" & 2-1/2" to 2"
- Shop: Pollak 5th Wheel / Gooseneck T-Connector with 7-Pole - Chrysler, Dodge w/ Factory Plug
- Shop: Gen-Y Torsion 2-Ball Mount - 2-1/2" Hitch - 3" Rise/6" Drop - 32K
- Shop: Gen-Y Torsion 2-Ball Mount - 2-1/2" Hitch - 2-1/2" Rise/5" Drop - 16K
- Q&A: TorkLift SuperHitch Magnum TL49YR The Same As D1110-30
- Shop: Buyers Products Fabricators Hitch Plate - 5/8" x 34-1/2" x 15-1/2"
- Q&A: Pintle Hitch Plate For 1997 Ford L8000 Dump Truck
- Q&A: Trailer Hitch Recommendation for 1954 Ford F-250
- Q&A: Can a Trailer Hitch be Installed on the Back of a Trailer
- Q&A: Dimensions of Curt Trailer Hitch Receiver C15800 for Ram Cab and Chassis
- Q&A: Recommended Class V Hitch for a 2017 Ram 3500
- Q&A: Why Can't the Curt SecureLatch be Used in the Rise Position
- Video: Detailed Breakdown of the Gen-Y Torsion 2-Ball Mount w/ Stacked Receivers
- Video: A Closer Look at the B&W Tow & Stow Pintle Hook for 2-1/2" Hitches
- Video: Review of Weigh Safe Pintle Hitch - Pintle Hitch Built In Scale Balls 2-1/2 Inch Hitch - WS52ER
- Video: Review of Gen-Y Hitch - Adjustable Stabilizer Bar Kit - GY69ER
- Video: Buyers Products Pintle Hitch - Pintle Hook - Air Compensated - 337P45AC6K Review
- Video: Gen-Y Torsion Pintle Hook Mounting Plate for 2-1/2" Hitches: The Breakdown
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Article: Trailer Wiring Diagrams
on Trailer Hitch
