Front Mount Trailer Hitch that Mounts Under the Bumper for a 2002 Jeep Wrangler

Question

Question:

Atop the front bumper are both tow hooks and fog lamps neither of which I will remove. Do you offer a bolt on hitch that will work for this vehicle? Your p/n 31408 is not acceptable.

asked by: Mcknight

0

Expert Reply:

We do offer a front mount receiver that is designed to fit below the bumper on a 2002 Jeep Wrangler. Take a look at CURT Front Mount Receiver, # C31028. I have included a link to the installation instructions. As you will see in the instructions, this hitch fits below the bumper and attaches to the vehicle frame. Even though there is some drilling required for installation, you will not need to remove anything mounted on top of the bumper.

expert reply by: Michael H

0

Answer 1

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Answer 2

Hi Stan! The SnowBear Snowplow for 2" Hitches - 82" Wide x 19" Tall #K2AVAL8219 and Curt Front Mount Trailer Hitch Receiver - Custom Fit - 2" #C31018 will definitely work on your 2013 Ford F-250 4x4. We actually have both of these…

view full answer...

Answer 3

Hey Dean, the Detail K2 Elite Snowplow part #K2AVAL8219ELT that you referenced comes with all of the electrical components it will need to install. It wires to the vehicle battery as well as comes with a wired switch that you would run to the cab of…

view full answer...

Answer 4

Hey Gary. The Draw-Tite Front Hitch item #65031 is going to mount a bit higher on your 2004 Toyota Tundra compared to the Curt item #31180. The Curt Front Hitch item #31180 is 14-3/4" off the ground when measured from the top of the inside of…

view full answer...

Answer 5

Hey Doug, I checked with Curt and their hitch part #C58VV is a confirmed for all models of the 2026 Lexus RZ350e including the electric model so it would work great for you. Do you have a bike rack already? What kind of bikes do you have?

view full answer...

Answer 6

I had our warehouse measure each of the front mount trailer hitch receivers you mentioned, and the dimensions are as follows. The Curt #31408 measures 32-3/4" long x 8-3/4" wide, the Draw-Tite #65080 measures 36-3/4" long x…

view full answer...

Answer 7

To install the Front Hitch part #65048 on your 1997 Jeep Wrangler TJ you will use one of the holes on the bumper and then also use one of the sway bar bushing bolt holes. Check out the picture I attached for more info. I also attached a link to the…

view full answer...

Answer 8

The biggest difference between Curt Hitch #13430 and #13408 is that the #13430 has a round cross tube whereas the #13408 has a square cross tube. This difference is primarily an aesthetic difference since both of these hitches have the same towing…

view full answer...

Answer 9

Below is the general process for bleeding an electric over hydraulic brake actuator like #K71-650. Fill reservoir with NEW brake fluid. Never re-use brake fluid that has been salvaged or removed from another system. Remove the key from the breakaway…

view full answer...

Answer 10

For a brake controller I would recommend the Prodigy P3 Brake Controller part #90195 for basically every towing situation but especially for an electric over hydraulic setup like what you have. This is our best selling brake controller because of how…

view full answer...

Front Mount Trailer Hitch that Mounts Under the Bumper for a 2002 Jeep Wrangler

Products Featured in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching