Help Picking Out Replacement Wheel Bolt Part Number 6109 RT

Question

Question:

This stud is off a 2013 Ranger boat trailer with 6109 RT stamped on the head. Which part number do you go by for ordering from you? Thanks.

asked by: James R

0

Expert Reply:

I wasn't able to get exact info on your part number, but from the part number we know it's right hand thread wheel bolt like the part # RG02-020 which is a fine thread 1/2 inch diameter bolt with a 60 degree angled head.

The other most likely fit is the part # RG02-040 which has a 90 degree head. Do you have a picture of the bolt I can look at?

expert reply by: Jameson C

0

Answer 1

The Dexter DX7.5L A-60 brake actuating coupler, part #DX89FR would be a direct replacement for the Dexter 34044 Disc Brake coupler you mentioned.

view full answer...

Answer 2

That's a really good question, and there is a difference between the 7,500 lb Dexter DX7.5L A-60 actuators for disc brakes; the differences are both in what they fit, as well as their length. - 14" Long & Top-Mounted For 3" Wide…

view full answer...

Answer 3

The UFP 34044 is basically the Dexter DX7.5L A-60 part #DX89FR. The second number you mentioned is actually a phone number. But the #DX89FR would be an exact replacement for what you have.

view full answer...

Answer 4

The only thing I could find close to that part number is the 6109 which has dimensions of: A=(1/2)", B=(1 3/4)", C=(1/2)", D=(5/8)", E=(9/16)" If this is what you have, then the Trailer Hub Wheel Stud - Drive In - 1/2"…

view full answer...

Answer 5

I wasn't able to get exact info on your part number, but from the part number we know it's right hand thread wheel bolt like the part #RG02-020 which is a fine thread 1/2 inch diameter bolt with a 60 degree angled head. The other most likely…

view full answer...

Answer 6

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 7

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 8

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 9

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 10

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 11

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 12

The Demco Hydraulic Trailer Brake Actuator part #DM72VR should be a direct replacement for the Atwood 61101 Brake Actuator that you have now. This newest updated it rated at 7K instead of 6K. This is a bolt on option that mounts on 3" centers.…

view full answer...

Help Picking Out Replacement Wheel Bolt Part Number 6109 RT

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching