Width of Holes for U-Bolt on Bracket # PF1135-BKT

Question

Question:

What diameter of holes on the top for the U-bolt? are these sized froi 3/8, 7/17inch or 1/2inch diameter u-bolts? Thanks

asked by: Gregory P

0

Expert Reply:

The width of the holes you mentioned are .55 inches.

expert reply by: Jameson C

0

click to enlarge

Answer 1

I went out to our warehouse to take a couple measurements on the CE Smith Single Axle Trailer Fender #CE19504 that you referenced. The inside arch between the two side steps measures 30-5/8 inches long. The step itself which I believe is what you…

view full answer...

Answer 2

I was able to go out to the warehouse and measure the mounting brackets holes for the PF11X35W and found that it was 5-5/16 inches or 5.3125 inches. If these aren't an exact match, new holes can usually be drilled into the brackets to make them…

view full answer...

Answer 3

The CE Smith trailer fender #CE19504 measures 34-1/2 inches from the center of one mounting point to the center of the other. Mounting points are on the underside of the step parts of the fenders. The fender can also be attached via its skirt which…

view full answer...

Answer 4

The CE Smith Single Axle Trailer Fender w/ Top and Side Steps - Black Plastic - 14" Wheels - Qty 1 #CE19504 is my recommendation for you. It is 43-1/8 inches long x 11 inches wide x 12-1/2 inches tall which will give you a skirt height of 11-1/2…

view full answer...

Answer 5

While the CE Smith Single Axle Trailer Fender #CE19504 does not have an opening for a side marker light it can easily be drilled to accommodate a set of lights. The Optronics LED Mini Clearance or Side Marker Trailer Light #MCL13A2B can be installed…

view full answer...

Answer 6

The CE Smith Single Axle Trailer Fender with Top and Side Steps - Black Plastic - 14" Wheels, has a mounting point that measures, from center to center, 34-1/2 inches. These fenders come in either a quantity of one or two: - Quantity of 1: CE…

view full answer...

Answer 7

The Fulton Single Axle Trailer Fender part #F008584 and CE Smith Single Axle Trailer Fender part #CE19504 are both excellent replacement trailer fender options. Unfortunately, we cannot confirm fit on any one particular make/model. They are designed…

view full answer...

Answer 8

Th fender mounting brackets we offer designed for the CE Smith Single Axle Trailer Fenders like part #CE19504 is the CE Smith Galvanized Steel Step for Trailer Fender part #CE26212G. The slots in the top will attach to the frame using u-bolts (not…

view full answer...

Answer 9

There is a slight difference in the designs of the Fulton fender #F008584 and the CE Smith Fender #CE19504 but other than appearance there isn't a whole lot of difference. I have stood on a Fulton fender before and it did flex but it didn't…

view full answer...

Answer 10

The CE Smith Single Axle Trailer Fender w/ Top and Side Steps - Black Plastic - 14" Wheels - Qty 1 #CE19504 can be installed with a u-bolt around your trailer frame instead of drilling into the frame using CE Smith U-Bolt - Galvanized -…

view full answer...

Answer 11

The CE Smith Single Axle Trailer fender #CE19504 is designed to be used with 14 inch trailer wheels. The mounting brackets that you will need are #CE26098G-2. These L-shaped brackets are made of galvinized steel and sold in pairs. You will need two…

view full answer...

Answer 12

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Width of Holes for U-Bolt on Bracket # PF1135-BKT

Product Page this Question was Asked From

Continue Researching